background image

4

|

ni.com

|

NI CVS-1459RT Getting Started Guide

This is a Pollution Degree 2 device. Do 

not

 operate the device in an explosive atmosphere or 

where flammable gases or fumes may be present. Operate the device only at or below the 
pollution degree stated in the specifications. Pollution consists of any foreign matter—solid, 
liquid, or gas—that may reduce dielectric strength or surface resistivity. The following is a 
description of pollution degrees.

Pollution Degree 1—No pollution or only dry, nonconductive pollution occurs. The 
pollution has no effect.

Pollution Degree 2—Normally only nonconductive pollution occurs. Occasionally, 
nonconductive pollution becomes conductive because of condensation.

Pollution Degree 3—Conductive pollution or dry, nonconductive pollution occurs. 
Nonconductive pollution becomes conductive because of condensation.

Clean the device and accessories by brushing off light dust with a soft, nonmetallic brush. 
Remove other contaminants with a stiff, nonmetallic brush. The unit 

must

 be completely dry and 

free from contaminants before returning it to service.

You

 must

 insulate signal connections for the maximum voltage for which the device is rated. Do 

not

 exceed the maximum ratings for the device. Remove power from signal lines before 

connection to or disconnection from the device.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for 
electromagnetic compatibility (EMC) as stated in the product specifications. These requirements 
and limits are designed to provide reasonable protection against harmful interference when the 
product is operated in its intended operational electromagnetic environment.

This product is intended for use in industrial locations. There is no guarantee that harmful 
interference will not occur in a particular installation, when the product is connected to a test 
object, or if the product is used in residential areas. To minimize the potential for the product to 
cause interference to radio and television reception or to experience unacceptable performance 
degradation, install and use this product in strict accordance with the instructions in the product 
documentation.

Furthermore, any changes or modifications to the product not expressly approved by National 
Instruments could void your authority to operate it under your local regulatory rules.

Caution

To ensure the specified EMC performance, operate this product only with 

shielded cables and accessories.

Содержание CVS-1459RT

















Отзывы: