National Instruments cDAQ-9133 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 145

background image

1-38

|

ni.com

Chapter 1

Getting Started with the cDAQ Controller

NI-XNET CAN/LIN Connector

(NI cDAQ-9134/9135)

The NI cDAQ-9134/9135 controller features an NI-XNET

hardware-selectable interface port that supports CAN and LIN transceiver cables.

Users have the flexibility to choose the physical bus protocol by plugging in corresponding
external transceiver cables. The NI-XNET connector supports hot-swapping of transceiver
cables and can detect and identify external transceiver cable types. For information about
connecting to a CAN or LIN bus, refer to your NI-XNET transceiver cable operating
instructions.

Caution

To maintain product performance and accuracy specifications when using

the NI-XNET CAN/LIN port and NI transceiver cable(s), do not attach or mount the
transceiver overmold directly to the cDAQ controller. Mount the overmolded section
of the transceiver cable at least 50.8 mm (2.00 in.) away from the cDAQ controller.
By following the cooling outline requirements shown in Figures 1-10 and 1-11, the
NI transceiver cable will not affect the thermal performance of the system.

Caution

Do

not

hot-swap NI-XNET devices while the cDAQ controller is in a

hazardous location or connected to high voltages. If the cDAQ controller is not in a

7

white/brown

white/brown

white/brown

8

brown

brown

brown

Table 1-8.

Ethernet Cable Wiring Connections (Continued)

Pin

Connector 1

Connector 2

Straight Through

Crossover

Connector 1

Connector 2

Pin 1

Pin 1

Pin

8

Pin

8

«
...
46
47
48
49
50
...
»

Содержание cDAQ-9133


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для cDAQ-9133

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: GE Страницы: 425

Бренд: Ebyte Страницы: 35

Бренд: Eaton Страницы: 100

Бренд: Samson Страницы: 73

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

8271 Nways Ethernet LAN Switch

Бренд: IBM Страницы: 6

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

xPico 200 Series

Бренд: Lantronix Страницы: 7

Бренд: Lantronix Страницы: 3

Бренд: Lantronix Страницы: 15

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Бренд: Radware Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды