National Instruments cDAQ-9133 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 145

background image

© National Instruments

|

1-35

NI cDAQ-9132/9133/9134/9135/9136/9137 User Manual

Table 1-6.

LED Indications

LED

LED

Color

LED State

Indication

POWER

Green

Solid

The cDAQ controller is powered from the V1 input.

Yellow

Solid

The cDAQ controller is powered from the V2 input.

—

Off

The controller is not powered.

STATUS

Yellow

2 flashes
every few
seconds

The controller has detected an error in its software. This
usually occurs when an attempt to upgrade the software is
interrupted. Refer to the

Measurement & Automation

Explorer Help

for information about installing software on

the controller.

3 flashes
every few
seconds

The controller is in safe mode. Refer to the

Measurement &

Automation Explorer Help

for information about safe mode.

4 flashes
every few
seconds

The software has crashed twice without rebooting or cycling
power between crashes. This usually occurs when the
controller runs out of memory. Review your RT VI and
check the memory usage. Modify the VI as necessary to
solve the memory usage issue.

Continuously
flashing

The controller either booted into an unsupported operating
system, was interrupted during the boot process, or detected
an unrecoverable software error.

Solid

The controller is booting up.

Red

Continuously
flashing

An internal power supply has failed. Check front-panel I/O
and C Series module connections for shorts. Remove any
shorts and power cycle the controller. If the problem
persists, contact National Instruments.

—

Off

Normal operation.

USER1,
USER2

Green/
yellow

—

USER LEDs are controlled directly from your application.
You can define the USER1 and USER2 LEDs to meet the
needs of your application. You can use the system hardware
property node from the NI System Configuration API to
write a state to the USER LEDs.

(NI cDAQ-9132/9133/9134/9135/9136/9137 for
LabVIEW Real-Time)

You can also define a USER LED

in LabVIEW Real-Time by using the RT LEDs VI. For more
information about the RT LEDs VI, refer to the

LabVIEW

Help

.

«
...
43
44
45
46
47
...
»

Содержание cDAQ-9133


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для cDAQ-9133

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Бренд: Echelon Страницы: 40

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: CALEFFI Страницы: 2

Бренд: CALEFFI Страницы: 12

Бренд: Caliber Страницы: 6

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: H3C Страницы: 69

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды