National Instruments cDAQ-9133 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 145

background image

1-14

|

ni.com

Chapter 1

Getting Started with the cDAQ Controller

Note

You can configure network settings using MAX on a host computer. Refer to

the

LabVIEW Real-Time Target Configuration

topic of the

Measurement &

Automation Explorer Help

for information.

Note

You can configure the cDAQ controller to launch an embedded stand-alone

LabVIEW RT application each time you boot the controller. Refer to the

Building and

Deploying a Stand-Alone Real-Time Application

topic of the

LabVIEW Real-Time

Module Help

for more information about startup applications.

Connecting to the Network through the Ethernet Port

(NI cDAQ-9132/9133/9134/9135/9136/9137 for LabVIEW Real-Time)

Use a shielded

straight through Category 5 Ethernet cable to connect the cDAQ chassis to an Ethernet network.

1

Connect one end to RJ-45 Ethernet port 1 on the controller, and the other end directly to your
computer or any network connection on the same subnet as your computer. Refer to the

section for information about the Ethernet cable.

Caution

To prevent data loss and to maintain the integrity of your Ethernet

installation, do

not

use a cable longer than 100 m.

The cDAQ controller attempts to initiate a DHCP network connection at powerup. If the cDAQ
controller is unable to obtain an IP address, it connects to the network with a link-local IP address
with the form

169.254.x.x

. The host computer communicates with the cDAQ controller over

a standard Ethernet connection.

Troubleshooting Network Communication in the
LabVIEW Real-Time Controller

(NI cDAQ-9132/9133/9134/9135/9136/9137 for LabVIEW Real-Time)

If the cDAQ

controller cannot communicate with the network, you can perform the following troubleshooting
steps.

Note

Windows XP users may be required to manually install the USB driver on the

host computer. The USB driver is installed in the

National Instruments\

CompactRIO\Staging\USBLAN

directory.

1.

Use a USB A-to-B cable to connect the USB device port of the cDAQ controller shown in
Figure 1-1, to a USB port on the host computer.
When you connect the cDAQ controller to the host computer, the USB driver creates a
virtual network interface card and assigns an IP address to the cDAQ controller in the
format of

172.22.11.x

.

1

You can either use a shielded straight through Category 5 Ethernet cable or an Ethernet crossover cable to

connect the cDAQ chassis directly to your computer.

«
...
22
23
24
25
26
...
»

Содержание cDAQ-9133


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для cDAQ-9133

Бренд: Cansec Страницы: 45

Бренд: Cansec Страницы: 43

Бренд: Cansec Страницы: 32

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Eaton Страницы: 2

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

Бренд: R82 Страницы: 89

Бренд: Patron Страницы: 17

Бренд: GEA Страницы: 13

Бренд: Cardin Elettronica Страницы: 56

Бренд: Belimo Страницы: 2

Бренд: Watts Страницы: 12

Бренд: Parallel Audio Страницы: 4

Бренд: Bardiani Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды