manualshive.com logo in svg

National Instruments AT-MIO/AI E Series, Руководство пользователя

Поделиться
Скачать
National Instruments AT-MIO/AI E Series Скачать руководство пользователя страница 54

Chapter 4     Signal Connections

 National Instruments Corporation

4-5

AT-MIO/AI E Series User Manual

I/O Connector Signal Descriptions

Signal Name

Reference

Direction

Description  

 

 

AIGND

—

—

Analog Input Ground—These pins are the reference point 
for single-ended measurements and the bias current return 
point for differential measurements.  All three ground 
references—AIGND, AOGND, and DGND—are connected 
together on your AT E Series board.

ACH<0..15>

AIGND

Input

Analog Input Channels 0 through 15—Each channel pair, 
ACH<i, i+8> (i = 0..7), can be configured as either one 
differential input or two single-ended inputs.

ACH<16..63>

AIGND

Input

Analog Input Channels 16 through 63 (AT-MIO-64E-3 
only)—Each channel pair, ACH<i, i+8> (i = 16..23, 32..39, 
48..55), can be configured as either one differential input or 
two single-ended inputs.

AISENSE

AIGND

Input

Analog Input Sense—This pin serves as the reference node 
for any of channels ACH <0..15> in NRSE configuration.

AISENSE2

AIGND

Input

Analog Input Sense (AT-MIO-64E-3 only)—This pin 
serves as the reference node for any of channels ACH 
<16..63> in NRSE configuration.

DAC0OUT

AOGND

Output

Analog Channel 0 Output—This pin supplies the voltage 
output of analog output channel 0.  This pin is not available 
on the AT-AI-16XE-10.

DAC1OUT

AOGND

Output

Analog Channel 1 Output—This pin supplies the voltage 
output of analog output channel 1.   This pin is not available 
on the AT-AI-16XE-10. 

EXTREF

AOGND

Input

External Reference—This is the external reference input for 
the analog output circuitry.  This pin is not available on the 
AT-MIO-16XE-10, AT-AI-16XE-10, or 
AT-MIO-16XE-50.   

AOGND

—

—

Analog Output Ground—The analog output voltages are 
referenced to this node.  All three ground references—
AIGND, AOGND, and DGND—are connected together on 
your AT E Series board.

DGND

—

—

Digital Ground—This pin supplies the reference for the 
digital signals at the I/O connector as well as the +5 VDC 
supply.  All three ground references—AIGND, AOGND, 
and DGND—are connected together on your  AT E Series 
board.

Содержание AT-MIO/AI E Series






















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды