manualshive.com logo in svg

National Instruments AT-GPIB/TNT, Начало работы, Страница: 51 / 64

Поделиться
Скачать
National Instruments AT-GPIB/TNT Скачать руководство пользователя страница 51

Appendix B

Troubleshooting and Common Questions

©

 National Instruments Corporation

B-7

AT-GPIB/TNT for Windows 98/95

Single-Cycle DMA Required

This error occurs if the Diagnostic utility detects that it is unable to 
perform demand-mode DMA for the GPIB interface and that the GPIB 
software has not been configured to use single-cycle DMA. GPIB 
interfaces that use the system DMA controller (such as the 
AT-GPIB/TNT) normally use demand-mode DMA. If you get this error, 
you should use the Device Manager to configure the GPIB software to 
use single-cycle DMA for all DMA transfers, and then run the 
Diagnostic utility again.

To configure the GPIB software to use single-cycle DMA for a 
particular GPIB interface, complete the following steps:

1.

Double-click on the System icon under Start»Settings»Control 
Panel. 

2.

In the System Properties dialog box that appears, select the 
Device Manager tab.

3.

Click on the View devices by type button at the top of the 
Device Manager page.

4.

Double-click on the National Instruments GPIB Interfaces icon.

5.

Double-click on the GPIB interface to be configured.

6.

Select the GPIB Settings tab.

7.

Click on the Advanced button and make sure that the Demand 
Mode DMA item is unchecked. 

GPIB Software Problem Encountered

This error occurs if the Diagnostic utility detects that it is unable to 
communicate correctly with the GPIB hardware using the installed 
GPIB software. If you get this error, shut down your computer, restart 
it, and run the Diagnostic utility again. If the problem persists, try 
reinstalling the GPIB software.

Unknown Problem Encountered

This error occurs if an unknown problem is encountered while trying to 
execute the Diagnostic utility. If you encounter this problem, shut down 
your computer, restart it, and run the Diagnostic utility again. If the 
problem persists, try reinstalling the GPIB software.

Содержание AT-GPIB/TNT

































































Отзывы:

Нет отзывов