National Cycle Wash'n'Wipe N30006-WK Скачать руководство пользователя страница 1

Thank you for purchasing a National Cycle product. Read these instructions carefully and thoroughly before beginning work. Dealers, if installing this 
windshield for a customer, please give them this manual upon completion. It contains information needed to properly maintain and use this product. 

N30403-WK PARTS LIST 
ITEM   PART NO.               DESCRIPTION                                       QUANTITY

 

 

A

        80-875150-000       Wiper Motor Assembly with Switch                         1 

B

        80-875153-000       Wiper Assembly Arm, 350mm (14.00")                   1 

C

        80-875155-000       Wiper Assembly Blade, 400mm (16.00")                1 

D

        44-442523-000       Reservoir & Pump Assembly                                  1 

E

        37-373694-000       Reservoir Mounting Bracket                                    1 

F

        75-766830-000       Gasket, 54.75" (139cm)                                          1 

G

        75-766831-000       Gasket, 26.5" (67cm)                                              1 

 

BAG#1324 
H

        80-830326-000       Wire Harness and Switch                                        1 

I

          80-875157-000       M8 Stud Hardware Kit                                             1 

J

         80-875156-000       Spindle Hardware Kit                                              1 

K

        44-447167-000       Rubber Grommet, Small                                         1 

L

        44-441927-000       Inline Check Valve for Washer Tubing                    1 

M

        44-448726-000       Wire Tie, 7.50" x .18                                                6 

N

        55-562600-000       Machine Screw, Panhead, Slotted, 10-32 x 5/8      2 

O

        49-490543-000       Flat Washer, .253 x .875 x .05                                2 

P

        42-450024-000       Nylok Hex Nut, 10-32                                              2 

Q

        5207                        Wellnut                                                                    2 

R

        55-581009-000       Screw, 10-32x.875 Stainless                                   2 

S

        44-449375-000       Wraparound Clamp                                                 1 

T

        75-764022-000       Rubber Clamp Spacer, .75x6.0                               1 

U

        44-449380-000       Grommet Retaining Pin                                           1 

V

        44-447159-000       Rubber Grommet, Large                                         1 

W

       44-448705-000       Cable Clamps                                                          1 

X

        55-563131-000       Screw, 12x.125, Stainless                                       1

 
TOOLS REQUIRED FOR ASSEMBLY

 

 
Flat Blade Screwdriver 
#2 or #3 Phillips Screwdriver or Phillips Bit for Drill  
T-25 Torx Wrench 
1/4", 5/16" and 7/16" Wrench or Socket 
10mm Wrench for Battery 
Metal Scribe or Marker 
X-Acto® Knife, or similar  
Wire Cutters  
Power Drill with 3/4" (19mm) hole saw or step drill bit 
Small Drill Bits (1/16" or 3/32", 1/8") for pilot holes 
Torque Wrench

National Cycle, Inc.

 PO Box 158 Maywood, IL 60153-0158 USA         P: 708-343-0400 / F: 708-343-0625 / E: [email protected]         

www.nationalcycle.com

©2021 National Cycle, Inc.

Page 1 of 14

10-118017-000 Rev A   04/21

Description:

Wash'n'Wipe Kit for N30006 
Full Size WIndshield

Model:

Honda® Pioneer 1000

Part Number:

N30006-WK

Installation Time:

60-90 min.

Quantum® is a registered trade-
mark of National Cycle Inc.

Assembly Instructions 
and Owner’s Manual

 

Содержание Wash'n'Wipe N30006-WK















Отзывы: