Napoleon NZ3000 страница 8 Скачать руководство пользователя | Manualshive

Страница: 8 / 48

background image

W415-0711 / D / 05.09.13

8

EN

To operate this hi-effi ciency appliance as a basic system, the blower is not required, however, to enhance its
effi ciency a blower is recommended.

2.6 HI-EFFICIENCY

HEATING

2.6.1 HOT AIR GRAVITY VENT SYSTEM (NZ220)

ALL HOT AIR GRAVITY VENTS MUST BE INSULATED.

May be used to distribute heat to an
adjoining room (located either above,
or beside the room containing the
appliance) by way of vents, eliminating
the need of an additional blower.
While this system may be used in
conjunction with the optional blowers,
it could reduce the flow of hot air
being distributed to additional rooms.
It must be experimented with and the
dampers adjusted manually to suit your
requirements. This may take a few
attempts; thereafter adjustments should
no longer be required as is normally
experienced with your central heating
system registers.

No more than

two

hot air gravity vents can be installed to
appliance. Individual vent runs are not to
exceed 10 feet (3m).

5 FT (1.5M)

MINIMUM

FROM FLOOR

5 FT (1.5M)

MINIMUM

FROM FLOOR

GROUND FLOOR

12” (304.8MM)

MINIMUM PIPE

TO CEILING

NO

DUCTING

GRAVITY VENT

OPTION (1 DUCT)

GRAVITY VENT

OPTION (2 DUCTS)

CENTRAL HEATING &

GRAVITY VENT OPTION

GRAVITY VENT OPTION

SIDES

ONLY

When installed with a masonry chimney, the hot air gravity and central heating system can only be installed off the sides.

*

*

«
...
6
7
8
9
10
...
»

Содержание NZ3000

















































Отзывы:

Нет отзывов

Похожие инструкции для NZ3000

Бренд: HAMPTON BAY Страницы: 9

COLLETTE L-FT629PST-A

Бренд: HAMPTON BAY Страницы: 6

Бренд: HAMPTON BAY Страницы: 48

Бренд: IHP Страницы: 2

Бренд: Jet-Line Страницы: 6

Бренд: Paloform Страницы: 16

Бренд: LA NORDICA Страницы: 76

Бренд: Regal Flame Страницы: 9

Бренд: Superior Fireplaces Страницы: 28

Ascent BHD4PFCNA

Бренд: Napoleon Страницы: 140

739CLK Classic Log Kit

Бренд: Valor Страницы: 4

Royale ETR Freestanding

Бренд: Rinnai Страницы: 16

Бренд: Mainstays Страницы: 48

GreenSmart Fireplace 564 SS

Бренд: Travis Industries Страницы: 28

Бренд: Travis Industries Страницы: 3

Бренд: Travis Industries Страницы: 2

Бренд: Travis Industries Страницы: 5

Бренд: Travis Industries Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды