StarLink
™
SLE Commercial LTEVI & LTEAI Series Dual-Path Alarm Communicators -- Installation Instructions
3
When processing an alarm, this LED will blink variably
during each part of the process (dialing, handshaking,
data transmission, etc.).
RED TROUBLE LED
Labeled "
D5
", this LED is located at the bottom right of
the PC board. Operation is as follows:
1 Blink:
Low Aux Power input voltage
2 Blinks:
Battery trouble
3 Blinks:
Alarm report Failed to Communicate (will
restore only when the radio path is restored)
4 Blinks:
RF trouble (antenna connection or cellu-
lar registration)
5 Blinks:
Radio poll or check-in failure (radio and/or
Ethernet). Either or both paths will trigger the trouble,
but for the trouble to clear, unit requires both IP and
radio polling/checkins to be operational
6 Blinks:
Unit disabled (reporting or control panel
downloading not allowed)
7 Blinks:
Unit was shutdown and has no function-
ality; requires a restart (full power down and full power
up sequence) to restore operation
8 Blinks:
Telco Line Cut
RED DIAGNOSTIC LED
Labeled
"
D7
", this LED is located in the middle of the PC
board. One blink indicates a weak or non-existent signal
from the network (green LED is off). If this red LED is
blinking in any other manner, contact technical support.
GREEN IP NETWORK CONNECTION LED
Labeled
"
D14
" (or
DS14
), this LED is located to the right
of the
ETHERNET
socket on the PC board. Operation is
as follows:
Off
= No network cable detected
Fast Flash
= No IP connection (Occurs just after pow-
er on, while trying to obtain a IP address)
Slow Flash
= Normal IP network operation
1 Blink:
Static IP
2 Blinks:
DHCP
3 Blinks:
Auto IP (If unable to acquire DHCP ad-
dress, then after 5 minutes it will convert to Auto IP
relay. Add shunt to lower two pins of JP1 for wet
contacts.
TB20: C OUT1:
Common. Dry contact Form C relay.
Add shunt to lower two pins of JP1 for wet contacts
(connects relay Common to system ground). Relay
rated 30V AC/DC, 500mA.
TB21: N/C OUT1:
Normally closed. Dry contact Form
C relay. Add shunt to lower two pins of JP1 for wet
contacts.
TB22: N/O OUT2:
Normally open. Dry contact Form C
relay.
TB23: C OUT2:
Common. Dry contact Form C relay.
Relay rated 30V AC/DC, 500mA.
TB24: N/C OUT2:
Normally closed. Dry contact Form
C relay.
LED DESCRIPTIONS
The PC board contains several LED's, as follows:
GREEN RF SIGNAL STRENGTH LED
Labeled
"
D3
", this LED is located at the lower right corner
of the PC board.
Every 30 seconds, the StarLink radio receiver section
turns on and listens to the cell tower. Depending on the
signal strength detected, it will blink the Signal Strength
LED from 1 to 5 times, providing a signal strength indica-
tor that is updated constantly and is always displayed.
Green LED Operation
Signal strength (as received by the radio) is displayed by
this LED blinking 1 to 5 times at a constant rate (with a
short delay between blink cycles).
Acceptable power lev-
el is greater than or equal to 2 blinks
.
YELLOW OPERATIONAL STATUS LED
Labeled "
D4
", this LED is located at the bottom right of
the PC board. Operation is as follows:
Normal Standby Condition:
Blinks on momentarily every 10 seconds:
Unit is in
standby waiting for an alarm to report.
Processing Alarm Conditions:
FIRE PROGRAMMING OPTION
PERMITTED IN
UL864? (Y/N)
AVAILABLE SETTINGS
REQUIRED UL 864 SETTINGS
Unattended Remote Downloading
No
Enable / Disable
Disabled (Jumper 1 installed). Also required for Commercial installations.
Note:
See page 7 "
Configuration Download / Firmware Updates
" for jumper instruc-
tions.
IN2
and
IN3
Unsupervised
Yes
Supervised / Unsupervised
Unsupervised using conduit within 20 feet of FACP (default). If not using conduit,
install Jumpers 4 and 5 and EOL Resistors. Inputs 2 an 3 can be unsupervised
with jumpers 4 and 5 removed; IN4 and IN5 always require EOLR
7 Day Supervision, Radio to NOC
No
200 seconds, 5 minutes, 6
minutes, 60 minutes, 6
hours, 7 days
200 seconds, 5 minutes, 60 minutes. 6 Hours permitted in Commercial Fire UL
864 with Dual Path enabled.
Trouble on Radio or IP Path
(Annunciate / Report)
Yes
Either Path or Both Paths Either Path (annunciation and report of trouble)
NOTICE TO AUTHORITIES HAVING JURISDICTION, USERS, INSTALLERS,
DEALERS, AND OTHER AFFECTED PARTIES
Wi-Fi Module
Yes
Enable / Disable
May be enabled as a primary reporting path for Fire