StarLink
™
SLE-LTEVI-FIRE & SLE-LTEAI-FIRE Commercial Series Dual-Path Alarm Communicators -- Installation Instructions
1
SLE-LTEVI-FIRE
&
SLE-LTEAI-FIRE
- Commercial / Resi-
dential Fire LTE Network Compatible alarm capture
Communicator. SIM card included. Red plastic enclo-
sure. Rated nominal 12/24VDC input.
ADDITIONAL COMPONENTS
In addition to the
SLE-LTEVI-FIRE
and
SLE-LTEAI-FIRE
listed above, the following sub-assemblies are available:
SLE-WIFI-MODULE
- Allows your Napco StarLink
™
device
to connect to the Internet by means of a wireless (Wi-Fi)
link, eliminating a wired Ethernet cable connection.
Note:
7AH battery required when using the
SLE-
WIFI-MODULE
. For more information, see WI2191.
SLE-DLCBL
- Download Cable, 6 feet.
SLE-ANTEXT30
- Extended antenna with 30 feet of cable
SLE-ANTEXT50
- Extended antenna with 50 feet of cable
SLE-ANTEXT75
- Extended antenna with 75 feet of cable
SLE-ANTEXT100
- Extended antenna with 100 feet of cable
(Any suitable external cellular antenna is permitted by
UL). Always follow the manufacturer's installation in-
structions.
Note:
Antennas are not Listed by UL.
SPECIFICATIONS
Electrical Ratings for +12V / 24V (powered by the con-
trol panel)*
Input Voltage: 10-25VDC regulated (power-limited out-
put from Listed control panel Aux/Remote Fire Power).
Input Current:
10VDC standby: 162mA
12VDC standby: 125mA
15VDC standby: 110mA
24VDC standby: 100mA
25VDC standby: 100mA
Wi-Fi Module:
(Optional) Add 40mA to the above.
(With peak RF transmission current of 325mA).
Electrical Ratings for the IN 1 Fire Input:
Input Voltage: 9-25VDC.
Maximum Input Current: Up to 2mA from FACP NAC
circuit
Electrical Ratings for IN 2, IN 3, IN 4, and IN 5:
(Inputs
IN 2, IN 3, IN 4, and IN 5 are
Class B)
Maximum Loop Voltage: 25VDC input.
Maximum Loop Current: 1.7mA
WI2326E.bLF 11/20
R
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, (800) 645-9445
For Technical Service, (800) 645-9440 or visit us at
http://tech.napcosecurity.com/
(Note: Technical Service is for security professionals only)
Publicly traded on NASDAQ Symbol: NSSC
© NAPCO 2020
INTRODUCTION
The
SLE-LTEVI-FIRE
and
SLE-LTEAI-FIRE
Dual-Path
Alarm Communicators
are specifically designed to interface
with FACP (Fire Alarm Control Panels) and to comply with
UL 864. The communicators are equipped with two dry
relays, one for a trouble output and one for an auxiliary out-
put. The units are also equipped with four supervised in-
puts to report a Fire Alarm, a Fire Trouble, a Water Flow
Alarm and a Supervisory Alarm, each triggered from the
N/O and Common terminals of the associated FACP output
relays. These communicators are for use as the primary
means of communication with the central station and do not
have backup mode capability. Dual Path Communicators
can also be utilized as a Sole Path Cell Communicator. No
POTS (Telco Line) connection permitted.
When connected to a FACP with one or two standard RJ-
45 telephone inputs, the
SLE-LTEVI-FIRE
and
SLE-LTEAI
-FIRE
provide two RJ-45 outputs to satisfy both telephone
inputs. The primary RJ-45 output is supervised and reports
a trouble to the central station upon any open or short on
the primary RJ-45 wires that prevent reporting. The sec-
ondary telephone line is supervised by the FACP; when a
line fault is detected, a trouble is reported to the central
station through the primary telephone line.
The
SLE-LTEVI-FIRE
and
SLE-LTEAI-FIRE
are compati-
ble with most 12 or 24VDC alarm control panels (always
adhere to the documentation provided by the control panel
manufacturer). Mount to a single-, dual-, or three-gang
electrical box and route the wires through the back knock-
out(s), or as specified by local codes.
See WI2140 for pro-
gramming information.
The
SLE-LTEVI-FIRE
and
SLE-LTEAI-FIRE
communica-
tors use proprietary data-capture technology that captures
the alarm report from the control panel and transmits the
alarm signals to the SLE Control Center; the alarm signals
are then forwarded to ANY central station via Contact ID or
4/2 via DACT from the NOC or Sur-Gard System II, Sur-
Gard System V, Bosch D6100IPV6 or Bosch D6600 Re-
ceiver (with ITS-D6686 Ethernet Adapter) via TCP/IP using
standard line security. The SLE Control Center reports a
trouble signal in the event that the network does not re-
ceive the expected supervision signal from the wireless
communicator. In addition, the
SLE-LTEVI-FIRE
and
SLE-
LTEAI-FIRE
are powered directly from the control
panel.
Note:
UL Listed for UL 1076 APOU Proprietary
Alarm Systems and UL 365 APAW Police Connect when
reporting to a UL Listed Central Station Receiver Listed for
UL 1076 APOU Proprietary Alarm Systems or UL 365
APAW Police Connect, respectively. For TCP/IP only
Bosch D6600 or D6100IPV6 for UL1076 and UL365 appli-
cations.
StarLink™ Commercial
SLE-LTEVI-FIRE & SLE-LTEAI-FIRE
Dual-Path Alarm Communicators
INSTALLATION INSTRUCTIONS
*For Commercial Fire installations, a UL Listed Fire Alarm regulated power
supply or FACP regulated auxiliary output is required.
AGENCY LISTINGS
UL 864 Standard For Control Units and Accessories For Fire Alarm
Systems, 10th Edition
UL 1610 Standard For Central-Station Burglar-Alarm Units
UL 985 Standard For Household Fire Warning System Units
UL 1023 Standard For Household Burglar-Alarm System Units
UL 1076 APOU Proprietary Alarm Systems
UL 365 APAW Police Connect
NYC Fire Dept. Certificate of Approval #6317 & 6318