NAPCO GEMINI GEMC-255 Скачать руководство пользователя страница 23

Страница: 23 / 72

NAPCO Gemini C-Series Control Panel Installation Instructions--Volume 2

Installation Instructions, Volume 2 Page 23

FIRE GLOSSARY

Clear Program

Caution:

Erases the dealer program. Use this feature to start a new customized default program. Access address in the Pro-

gramming Instructions (WI1673), then press

ENTER

Coded Alarms by Zone

An initiating zone can be individually programmed, using PCD-Windows Quickloader, to activate one of thirty available ca-

dences on NAC circuits.

This feature is primarily used to assist in the identification of a particular area of a large facility, such as a hospital, where a

certain section of the hospital will sound a particular code during an alarm to allow people to select the correct egress method
or path.  This feature can also be used to allow schools to prevent evacuations caused by inappropriate use of pull stations.  If
a pull station is activated, a person with the authority to unlock the GEMC-FK1 Fire keypad (such as a teacher) could quickly
identify the location of the activated pull station and determine whether the alarm is warranted.  If not, the authorized person
would silence the alarm.  See

NAC Features

entry for a description of the ANSI 3.41 / Temporal cadence.

Program as follows:

1. Open the

NAC/Output Assignment

screen, click the

NAC/Output Options

tab, then check the

Coded Alarms by Zone

checkbox and the

Coded Alarm

column appears in the

Zone Assignment

screen (Ctrl + Shift + Z). Select a cadence for

each zone, as required.

2. Program at least one silence-able NAC output (typically all NAC outputs) for Enable Cadence (in the

NAC/Output As-

signment

screen, click the

NAC/Output Assignments

tab, then check the

Enable

checkbox for the selected output in

the

Cadence

column.

Daylight Saving Time

Enables Daylight Saving Time to be in effect within the selected account. Program using the Quickloader

Panel Selection

screen,

TimeZone - DST

tab. Programmable DST fields allow Daylight Saving Time to be adjusted for possible future

changes.

Dealer Keypad Program Code

This code is left blank in the control panel memory at the factory and may be added by the dealer (in possession of the

Master

Coded Alarm Type Options and Cadences

Note:

Each pulse (on-off) is in total 500mS. Each inter-digit duration is 750mS. Each inter-round duration is 1.5 seconds.

In the table below, each "1" = [250mS on, 250mS off]. Each "." = [250mS off].

Short

Format

Output (2 rounds shown)

Short

Format

Output (2 rounds shown)

Steady

1-4-4

1...1111...1111......1...1111...1111.......

1-1-1

1...1...1......1...1...1.......

2-1-1

11...1...1......11...1...1.......

1-1-2

1...1...11......1...1...11.......

2-1-2

11...1...11......11...1...11.......

1-1-3

1...1...111......1...1...111.......

2-1-3

11...1...111......11...1...111.......

1-1-4

1...1...1111......1...1...1111.......

2-1-4

11...1...1111......11...1...1111.......

1-2-1

1...11...1......1...11...1.......

2-2-1

11...11...1......11...11...1.......

1-2-2

1...11...11......1...11...11.......

2-2-2

11...11...11......11...11...11.......

1-2-3

1...11...111......1...11...111.......

2-2-3

11...11...111......11...11...111.......

1-2-4

1...11...1111......1...11...1111.......

2-2-4

11...11...1111......11...11...1111.......

1-3-1

1...111...1......1...111...1.......

2-3-1

11...111...1......11...111...1.......

1-3-2

1...111...11......1...111...11.......

2-3-2

11...111...11......11...111...11.......

1-3-3

1...111...111......1...111...111.......

10-1

1111111111...1…...1111111111...1…...

1-3-4

1...111...1111......1...111...1111.......

10-2

1111111111...11…...1111111111...11…...

1-4-1

1...1111...1......1...1111...1.......

1-4-2

1...1111...11......1...1111...11.......

ANSI 3.41 / Temporal (required in

UL 985 Residential Fire installations)

1-4-3

1...1111...111......1...1111...111.......

Содержание GEMINI GEMC-255









































































Результаты поиска

Содержание GEMINI GEMC-255

Отзывы:

NAPCO GEMINI GEMC-255, Руководство по установке, Страница: 23 / 72

Результаты поиска

Содержание GEMINI GEMC-255

Отзывы: