NANOTEC PD4-E Скачать руководство пользователя страница 281

Страница: 281 / 295

Technical Manual PD4-E-M (EtherCAT)
10 Description of the object dictionary

Subindex n contains the number of motor revolutions of the corresponding feedback.
Subindex 01

always corresponds to the first (and always existing) sensorless feedback.

The resolution of feedback "n" is calculated as follows:

Position Encoder Resolution = Encoder Increments (60E6

:01

) / Motor Revolutions (60EB

:02

)

60EDh Additional Gear Ratio - Driving Shaft Revolutions

Function

In this object and in 60E8

, you can set the gear ratio of each existing feedback.

Object description

Index

60ED

Object name

Additional Gear Ratio - Driving Shaft Revolutions

Object Code

ARRAY

Data type

UNSIGNED32

Savable

yes, category: application

Access

read only

PDO mapping

RX-PDO

Allowed values

Preset value

Firmware version

FIR-v1738-B501312

Change history

Value description

Subindex

Name

Highest Sub-index Supported

Data type

UNSIGNED8

Access

read only

PDO mapping

RX-PDO

Allowed values

Preset value

Subindex

- 03

Name

Additional Gear Ratio - Driving Shaft Revolutions Feedback Interface
#1 - #3

Data type

UNSIGNED32

Access

read / write

PDO mapping

RX-PDO

Allowed values

Preset value

00000001

Description

The subindices have the following function:

Version: 1.0.1 / FIR-v1748

281

Содержание PD4-E








































































































































































































































































































Результаты поиска

Содержание PD4-E

Отзывы:

NANOTEC PD4-E, Техническое руководство, Страница: 281 / 295

Результаты поиска

Содержание PD4-E

Отзывы: