N&W Global Vending Snakky RY, Руководство по установке

Страница: 20 / 52

© by N&W GLOBAL VENDING S.p.A.
16
06 2007 294-00
SpEcial SElEctioNS
v
irtUal selectioNs
This function is used to define a pair of selections that
can be sold at a price different from the sum of the two
selections, using a single selection number. 10 virtual
selections can be programmed (70 to 79).
r
etUrN of virtUal price
This function is used to define, in the event of failed
second dispensing in a virtual selection, not to cash the
price of the second selection (only if an MDB payment
system or validator are used). With other payment sys -
tems, it can be decided whether or not return the entire
amount.
s
electioNs witH two motors
In order to dispense long products, dividers can be fitted
so that two motors are used for each single selection.
With this function the operation of two motors can be
combined, specifying the selection number of the sec -
ond motor.
The first motor number will be the selection number,
while the selection number of the associated motor will
remain disabled.
important notice!!!
after a failure to the motors of these selections, the
machine configuration procedure in the “Spiral/Se -
lection” menu must be followed.
D
ispeNsiNg DetectioN
The vending machine can be fitted (as standard feature
or as optional according to the model) with a device that,
by means of photocells, detects the passage of dis -
pensed products.
This device permits, in the event of failed detection of the
dispensed product:
to set a rotation time for the spiral beyond the limit
-
switch, to overcome any jamming;
to return or not the paid amount;
-
to block further selections for the involved spiral.
-
tESt
s
electioNs
This function is used to simulate the normal dispensing
of products without inserting any money to check the
functioning of the spiral rotation by pressing the selec -
tion buttons.
m
otor test
It activates all motors in a sequence, indicating on the
display the number of the involved selection.
a
Utotest
A function to check, in a semiautomatic manner, the
correct operation of some devices is implemented in the
software
.
Some checks occur automatically, others need the
manual operation of the monitored component; button
�
is pressed to go to the next check.
The monitored devices are:
“keypad”
Press the button requested on the display; if it works cor -
rectly the request for the next button is presented.
“temperature”
The value of temperature detected by the probe is dis -
played.
In the event of disconnection the value -11.0 is dis -
played.
In the event of a short-circuit the value 41.0 is displayed.
“buzzer”
A series of sounds is emitted to check the functioning of
the buzzer.
“compressor”
The compressor is activated/deactivated using the
�
and
�
buttons.
“Selections”
All selections are activated in a sequence.
“coin mechanisms”
Checking that communication with the coin mechanism
takes place correctly and which validator lines are set as
being active.
“photocells”
If the product detection device is present, the light beam
reading and interruption are checked.
“disp compt lock”
If the device for locking the dispensing compartment
opening, use the
�
and
�
buttons to lock and unlock
the compartment opening.
GSM Pre-alarMS
The control software can send, via GSM modem, a
signal indicating an “ending product” signal, when there
is only a certain (programmable) number of pieces of a
given product left.
With this function the counters that control the pre-
alarms are reset.
EvadtS tRaNSfER
When activating this function, the machine awaits the
connection with a device to acquire the EVADTS statis -
tics.
FILL>
GSM
FILL>
Reset pre-alarm counters
�
�
FILL>
EVADTS
FILL>
Connection
�
�