background image

© by N&W GLOBAL VENDING S.p.A. 

13

 

06 2007 294-00

 

Notes on programming

The machine electronic control allows the use of many 

functions.

The machine is supplied with a selection layout, describ

-

ing the different selections available for the specific 

model and the flowchart of the programming menu.

Below there is a summary explanation of the main func

-

tions useful for managing the operation of the machine, 

not necessarily in the order in which they are displayed 

in the menu.

The machine software can be updated using the specific 

systems (PC, Flash, UpKey etc.).

Power-on

When closing the machine door, the display indicates 

the version number of the installed software.

The machine can be programmed for displaying, for a 

few second, the number of selections made.

After a few seconds the machine goes into normal vend

-

ing mode and the display shows the message for the 

user prompting to select a product.

opERatiNg modES

Three different operating modes are provided for the 

machine; the buttons will have different functions accord

-

ing to the machine operating mode.

The available operating modes are as follows:

 

   

FUnctIons

Normal vending mode    

Coins are accepted

 

   

Products dispensed

Filler menu 

   

Test dispensing

 

   

machine maintenance

technician menu 

   

Programming 

   

the parameters

According to the operating mode, the display and 

keypad functions change as described in the following 

paragraphs.

NoRmal vENdiNg modE

During the normal vending mode the lighting lamp is 

switched on and the display shows the message for the 

user prompting to select a product.

When inserting coins or a payment system, the available 

credit is displayed.

In the event of a malfunction detected by the control 

system, an error message will be displayed indicating 

the type of problem.

At the end of dispensing, for a few seconds the display 

indicates the message to pick up the product and the 

machine is preset for the next selection.

Snakky Ry

Rev x.x

SELECT THE PRODUCT

SELECT THE PRODUCT

Credit= 

0.50

SELECTION NOT AVAILABLE

“Failure name”

TAKE 

THE PRODUCT

Содержание Snakky RY





















































Отзывы: