NAMCO Vampire Night DX Скачать руководство пользователя страница 34

Страница: 34 / 85

Page 33

4. MOVING THE MACHINE

This equipment is fitted with castors to make it easier to move. Take care when

moving the equipment on an inclined floor.

The overall height of this equipment is 2230mm. Take care of any overhead

obstructions. (e.g. Light Fittings, Electric Cables etc.)

WARNING

NEVER turn the power to the machine ON until installation

has been completed.

WARNING

In order to prevent possible electric shocks, be sure that the

machine is connected to the mains with a securely connected

earthed plug.

WARNING

So that customers are not injured , ensure that there is at

least 500mm separation between other machines or walls.

CAUTION

In order to avoid damage to the machine due to mis-operation,

ensure that the voltage of the mains supply is 230volts AC.

5. INSTALLATION

Notes on Installation

NOTE

If the location site of this machine has a polished floor it is

recommended that rubber pads are fitted under the level adjusters

to prevent the machine sliding on the floor.

In order to gain access to the Power Supply and CPU assemblies,

make sure that the rear of the machine is separated from a wall

or other machine by at least 500mm.

When installation is complete, it is imperative that the guns are

initialized.

(See section 6-2-3-1 page 47)

Содержание Vampire Night DX






















































































Результаты поиска

Содержание Vampire Night DX

Отзывы:

Похожие инструкции для Vampire Night DX

Бренды по названию

Популярные бренды

NAMCO Vampire Night DX, Руководство оператора

Результаты поиска

Содержание Vampire Night DX

Отзывы:

Похожие инструкции для Vampire Night DX

Бренды по названию

Популярные бренды