background image

EM-3060

Brushless Motor

OPERATION MANUAL

002

OM-K0482E

Thank you for purchasing the Brushless Motor " EM - 3060 ". This Brushless Motor which can be connected with 
60,000min

-1

 (rpm) spindle. The E3000 CONTROLLER, Spindle, Motor Cord and Air Line Kit are required to drive 

this Brushless Motor. Read this and all the associated component Operation Manuals carefully before use. Always 
keep this Operation Manual in a place where a user can referred to for reference at any time.

 Read these warnings and cautions carefully and only use in the manner intended.

 These warnings and cautions are intended to avoid potential hazards that could result in personal injury to the 

operator or damage to the device. These are classied as follows in accordance with the seriousness of the risk.

Class

Degree of Risk

 WARNING

A safety hazard could result in bodily injury or damage to the 
device if the safety instructions are not properly followed.

 CAUTION

A hazard that could result in light or moderate bodily injury or 
damage to the device if the safety instructions are not followed.

CAUTIONS FOR HANDLING AND OPERATION

1.

This Brushless Motor is not a hand tool. It is designed to be used on CNC machines or special 
purpose machines.

Do not touch the cutting tool while it is running. It is very dangerous.

Wear safety glasses, dust mask, and use a protective cover around the Brushless Motor whenever 
the Brushless Motor is rotating.

Never connect, disconnect or touch the Power Cord Plug or Motor Cord Plug with wet hands. This 
may cause an electric shock.

Never operate or handle the Brushless Motor and spindle until you have thoroughly read the 
Operation Manuals and safe operation has been conrmed.
1) To prevent injuries / damages, check the Brushless Motor, spindle and cutting tool for proper 

installation, before operating the Brushless Motor and spindle.

2) Before disconnecting the Brushless Motor and spindle, always turn the control power off and 

turn the compressed air supply to the CONTROLLER off. Then it is safe to remove the Brushless 
Motor and spindle.

When installing a Brushless Motor to a xed base, make sure the xed base is grounded in order 
to avoid the risk of an electric shock.

 

 WARNING

Do not drop or hit this Brushless Motor, as shock can damage to the internal components.

Select suitable products or tools for all applications. Do not exceed the capabilities of the 
Brushless Motor or tools.

Do not stop the supply cooling air for Brushless Motor during operation of the machine.
Removing the air pressure from the Brushless Motor causes a loss of purging, allowing the 
Brushless Motor to ingest coolant. This will cause damage to the Brushless Motor.

Carefully direct coolant spray to the tool. Do not spray directly on the Brushless Motor body. If 
large amount spray directly on the Brushless Motor, it may cause excess load of the Brushless 
Motor rotation with loss of durability to the Brushless Motor.

Stop working immediately when abnormal rotation or unusual vibration are observed. Immediately, 
please check the content of section " 11. TROUBLESHOOTING ". 

Always check if the connection hose and supply air hose for damaged before and after operating.

After installation, repair, initial operation, or long periods of non operation, please carry out break 
-in as follow. Start rotating slowly and over a short period of 15 - 20 minutes, increase speed 
gradually until allowable maximum speed.

Do not disassemble, modify or attempt to repair this Brushless Motor. Additional damage will 
occur to the internal components. Service must be performed by NSK NAKANISHI or an authorized 
service center.

When using this Brushless Motor for mass production, please consider the purchase of an 
additional Brushless Motor to be used as a back-up in case of emergency.

Securely connect the compressor supply connection hose to the Air Line Kit, and connect the air 
hose to the Air Line Kit, CONTROLLER and the Brushless Motor to avoid accidental disconnection 
during use.

 

 CAUTION

BASIC PACKAGE

2.

When opening the package, check if it includes all items listed in " Table. 1 Packing List Contents ".
In the event of any shortage, please contact either NAKANISHI (see the " 4. CONTACT US " section) or your local 
dealer. 

Table. 1 Packing List Contents 

EM - 3060

・・

1pc.

Wrench (22 x 27)

・・

1pc.

27

22

Operation Manual

・・

1set

ྲྀᢅㄝ᫂᭩

OPERATION MANUAL

WARRANTY

3.

Defect in manufacturing.

Any shortage of components in the package.

Where damaged components are found when initially opening the package.
(This shall not apply if the damage was caused by the negligence of a customer.)

We provide a limited warranty for our products. We will repair or replace the products if the cause of failure is due to 
the following manufactures defects. Please contact us or your local distributor for details. 

CONTACT US

4.

For your safety and convenience when purchasing our products, we welcome your questions.
If you have any questions about operation, maintenance and repair of the product, please contact us.

Company Name

Business Hours

U.S. Toll Free No.
Telephone No.
Fax No.
Web Address

:

Industrial Div. 

:  8:30am to 17:00pm (CST)
   (closed Saturday, Sunday and Public Holidays)
:  800-585-4675
:  847-843-7664
:  847-843-7622
:  www.nskamericacorp.com

Contact Us

Contact Us

For U.S. Market

Company Name
Business Hours

Telephone No.
e-mail Address

:  
:  8:00am to 17:00pm
   (closed Saturday, Sunday and Public Holidays)
:  +81 (0) 289-64-3520
:  [email protected]

For Other Markets

FEATURES

5.

The Brushless Motor housing is made from precision ground, hardened, stainless steel (SUS) with an outside 
diameter of 

ȭ

30mm.

Excellent durability and high reliability are obtained by using a high-speed Brushless Motor, which eliminates 
the need for brush replacement and frequent maintenance.

The maximum output is 350W.

Air-cooling system with a small volume of air (30

/ min) is used to prevent heat buildup and allows long 

continuous operation.

SPECIFICATIONS AND DIMENSIONS

6.

6 - 1  Specications

Model

EM - 3060

Motor Rotation Speed

1,000 - 60,000min

-1

 (rpm)

Max. Output

350W

Weight

325g (without Motor Cord)

Noise Level at 1m distance

Less than 70dB (A)

Temperature

Humidity

Atmospheric Pressure

Operation Environment

0 - 40°C

MAX.75%
(No condensation)

800 - 1,060hPa

Transportation and Storage
Environment

-10 - + 50°C

10 - 85%

500 - 1,060hPa

<Option>

Motor Cord : <S Type> Straight

EMCD - 3000 - 4M (4m) / 6M (6m) / 8M (8m)
(The Air Hose (

ȭ

4mm) of the same length is attached.)

: <A Type> Angle

EMCD - 3000A - 4M (4m) / 6M (6m) / 8M (8m)
(The Air Hose (

ȭ

4mm) of the same length is attached.)

*Note 1 : Motor Cord is sold separately.

Please select the suitable motor cord length for your application.

6 - 2  Outside View

93.5

8.3

-0.02 -0.03

ȭ

30

(11)

34.5

Fig. 1

6 - 3  Torque Characteristics

T

o

rque (cN

m)

9

8

7

6

5

4

3

2

1

0

450

400

350

300

250

200

150

100

50

0

Output (W)

10

20

30

40

50

Speed (x10

3

min

-1

 (rpm))

Torque

Torque

Output

Output

Continuous Duty Area

Continuous Duty Area

Fig. 2

Отзывы: