background image

 

19 

   Y-KH15-007A Rev.3 

Induction noise 

•  Keep the product away from the wiring carrying high current. 
•  Keep the product away from electrically charged machines or objects. 

Conductive noise 

•  Use the stable power supply that is difficult to generate noise. 
•  Install power supply or output measurement equipment in an environment that is impervious to 

being affected by noise. 

•  Use a ferrite core to filter cables. 
•  Use high-noise-resistant cables such as a shield one for connection to connect the shield to the 

ground. 

 
 

11. STORAGE 

11.1 Precautions for Storage

 

 

 

Do not store the product in the places listed below. If you do not 
observe this instruction, the product will fail or get damaged. 

• 

Locations that are prone to condensation with high humidity 

• 

Locations that may be adversely affected by atmospheric 
pressure, temperature, humidity, ventilation, sunlight, dust, salt, 
sulfur-containing air or other factors 

• 

Locations subject to inclination, vibration  or  shock (including 
those during transportation) 

• 

Locations where chemicals are stored or gases are generated. 

• 

Locations exposed to direct sunlight or in high-temperature cars 

 
 

12. MAINTENANCE 

12.1 Periodical Inspection 

A periodical maintenance once a half year will be needed due to possible  aging under different 

operating conditions. Also, perform calibration as needed. Calibration should be performed in a 
specified manner or at a designated calibration laboratory.   

Refer to the following checklist for periodic inspections. 

 

< Periodic Inspection Checklist > 

 

Appearance (flaws, cracks, deformation, and corrosion) 

 

Corrosion state of the pressure inlet 

 

Insulation resistance between the case and all terminals tied 

(100 MΩ or more

 at 50V DC) 

 

Leak check and retightening of the threads 

 

Output check with a reference pressure gauge and a measuring instrument 

 

Waterproof check and retightening of the cable, gland, and terminal box 

 

CAUTION 

Содержание KH15 3 Series

























Отзывы: