NAD CI 8-120 DSP Скачать руководство пользователя страница 13

Страница: 13 / 16

ENGLISH

OPERATION

STANDBY MODES

STANDBY MODE

CONDITION

RESULT

Standby Mode 1

(Power Button)

Method A

• ECO mode : ON

• Power mode: Switch from other Power Mode (Always ON, 12V Trigger,

Signal Sense) to Power Button

• Unit will immediately go to standby mode after the switch to Power

Button mode.

Method B

• ECO mode : ON

• Power mode: Currently at Power Button and unit at operating mode

• Unit will immediately go to standby mode when front panel Standby

button is pressed.

Standby Mode 2

(12V Trigger)

Method A

• ECO mode : ON

• Rear panel 12V TRIGGER switch: ON

• Power mode: Switch from other Power Mode (Power Button, Always ON,

Signal Sense) to 12V Trigger

• Unit will immediately go to standby mode after the switch to 12V

Trigger mode.

Method B

• ECO mode : ON

• Rear panel 12V TRIGGER switch: ON

• Power mode: Currently at 12V Trigger and unit at operating mode

• Unit will immediately go to standby mode when 12V TRIGGER source is

turned off.

Standby Mode 3

(Signal Sense)

Method A

• ECO mode : ON

• All Sources are powered down or no signal output

• Power mode: Switch from other Power Mode (Power Button, Always ON,

12V Trigger) to Signal Sense

• Unit will immediately go to standby mode after the switch to Signal

Sense mode.

Method B

• ECO mode : ON

• All Sources are powered down or no signal output

• Power mode: Currently at Signal Sense and unit at operating mode

• Unit will go to network standby mode after 20 minutes of no active

audio source input.

Network Standby Mode 1

(Power Button)

Method A

• ECO mode : OFF

• Power mode: Switch from other Power Mode (Always ON, 12V Trigger,

Signal Sense) to Power Button

• Unit will immediately go to standby mode after the switch to Power

Button mode.

Method B

• ECO mode : OFF

• Power mode: Currently at Power Button and unit at operating mode

• Unit will immediately go to network standby mode when front panel

Standby button is pressed.

Network Standby Mode 2

(12V Trigger)

Method A

• ECO mode : OFF

• Rear panel 12V TRIGGER switch: ON

• Power mode: Switch from other Power Mode (Power Button, Always ON,

Signal Sense) to 12V Trigger

• Unit will immediately go to network standby mode after the switch to

12V Trigger mode.

Method B

• ECO mode : OFF

• Rear panel 12V TRIGGER switch: ON

• Power mode: Currently at 12V Trigger and unit at operating mode

• Unit will immediately go to network standby mode when 12V TRIGGER

source is turned off.

Network Standby Mode 3

(Signal Sense)

Method A

• ECO mode : OFF

• All Sources are powered down or no signal output

• Power mode: Switch from other Power Mode (Power Button, Always ON,

12V Trigger) to Signal Sense

• Unit will immediately go to standby mode after the switch to Signal

Sense mode.

Method B

• ECO mode : OFF

• All Sources are powered down or no signal output

• Power mode: Currently at Signal Sense and unit at operating mode

• Unit will go to network standby mode after 20 minutes of no active

audio source input.

Содержание CI 8-120 DSP

















Результаты поиска

Содержание CI 8-120 DSP

Отзывы:

Похожие инструкции для CI 8-120 DSP

Бренды по названию

Популярные бренды

NAD CI 8-120 DSP, Руководство пользователя

Результаты поиска

Содержание CI 8-120 DSP

Отзывы:

Похожие инструкции для CI 8-120 DSP

Бренды по названию

Популярные бренды