Mylex Disk Array controller Software Kit 2.01 Скачать руководство пользователя | Manualshive

Страница: 32 / 172

background image

Global Array Manager (GAM)Server Software for NetWare 4.11/4.2 and 5.0

2-12

Disk Array Controller Software Kit User’s Manual

Global Array Manager (GAM)Server Software for
NetWare 4.11/4.2 and 5.0

Utility Files for NetWare

The Global Array Manager Server for NetWare contains the following utility
files (not normally used at the same time as GAM):

DACMON.NLM:

A monitor utility to log and report controller
activities. A separate screen appears for each
controller detected. Screens are identified as
Dacmon1, Dacmon2, etc. (For more details, see “Disk
Array Monitor (DACMON) Utility for NetWare 4.11/
4.2 and 5.0” on page 2-17.)

DACADM.NLM:

Administrative utilities, consisting of various tools for
managing and maintaining a disk array. (For more
details, see “System Administration (DACADM)
Utility for NetWare 4.11/4.2 and 5.0” on page 2-19.)

m

Caution

These utilities can change the state of the disk array
system and are for use only by experienced system
administrators. Improper use of these utilities may
result in system malfunction or data loss.

Installing Global Array Manager Server Software

The Global Array Manager (GAM) Server software for NetWare has an
automated installation utility which is run from the NetWare server console.
This utility places the Global Array Manager Server application in the
correct server directory and modifies the NetWare startup file,
AUTOEXEC.NCF, to launch the application when the server is started.

☛

Note

These instructions assume that your CD-ROM drive is
properly identified and that CDROM.NLM is loaded.

«
...
30
31
32
33
34
...
»

Содержание Disk Array controller Software Kit 2.01













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Disk Array controller Software Kit 2.01

PT-D10000 Series

Бренд: Panasonic Страницы: 37

Бренд: On-Q/Legrand Страницы: 14

718659340025 - InDesign CS - PC

Бренд: Adobe Страницы: 122

Бренд: Adobe Страницы: 306

CONTRIBUTE-USING CONTRIBUTE

Бренд: MACROMEDIA Страницы: 214

Бренд: ZixCorp Страницы: 44

Бренд: Valgrind Страницы: 319

BlackArmor WS 110

Бренд: Seagate Страницы: 2

Xbox360 MotoGP08

Бренд: Capcom Страницы: 28

Бренд: F-SECURE Страницы: 219

SpeedUpMyPC 2010

Бренд: UNIBLUE Страницы: 11

Бренд: Mackie Страницы: 20

LogiCORE Endpoint v2.4

Бренд: Xilinx Страницы: 172

Бренд: IBM Страницы: 29

MOVI 4.0 - FOR WINDOWS 10-2010

Бренд: TANDBERG Страницы: 19

WII GAMESHARK CHEAT SAVES AND MEDIA MANAGER

Бренд: Saitek Страницы: 15

Бренд: Tascam Страницы: 33

Бренд: Brother Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды