Mylex Disk Array controller Software Kit 2.01 Скачать руководство пользователя | Manualshive

Страница: 13 / 172

background image

Manual No. 771929

1-1

Chapter 1

Introduction

Overview

This manual provides information on the following:

• How to install and use the Mylex Disk Array Controller Software Kit

operating system software drivers and utilities for Mylex Disk Array
Controllers

• How to install the Global Array Manager Server software for several

supported operating systems.

Disk Array Controller Operating System Driver and Utility
Installation Diskettes and CD-ROM

Mylex Disk Array Controller Operating System Drivers and Utilities in this
Software Kit v2.01 are delivered on a CD-ROM and the necessary diskettes.
Each diskette is used to install drivers and utilities to support one or more
network operating systems. The table on the next page summarizes the
contents of the installation diskettes (Table 1-1):

«
...
11
12
13
14
15
...
»

Содержание Disk Array controller Software Kit 2.01













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Disk Array controller Software Kit 2.01

NG Network Access Client SP4

Бренд: Barracuda Networks Страницы: 268

Бренд: Brocade Communications Systems Страницы: 60

8.5 EMAIL SERVER EDITION - V 85.4

Бренд: AVG Страницы: 52

Бренд: IBM Страницы: 481

Бренд: Casio Страницы: 18

Бренд: Omron Страницы: 2

DEVICE FILTER MAC

Бренд: FARONICS Страницы: 30

ST905003BPA1E1-RK - Maxtor BlackArmor 500 GB External Hard Drive

Бренд: Seagate Страницы: 2

ASSET MANAGEMENT SUITE 7.0

Бренд: Symantec Страницы: 4

ANTIVIRUS 5.2 - FOR NETWORK ATTACHED STORAGE

Бренд: Symantec Страницы: 3

Altiris CMDB Solution 7.0

Бренд: Symantec Страницы: 64

DriverScanner 2010

Бренд: UNIBLUE Страницы: 12

Бренд: Pantone Страницы: 12

SAMREPORT-LITE 2006

Бренд: Macrovision Corporation Страницы: 36

FLASH MX 2004 - ACTIONSCRIPT

Бренд: MACROMEDIA Страницы: 816

TonePrint Editor

Бренд: TC Electronic Страницы: 19

Powershot A3100 IS

Бренд: Canon Страницы: 60

ScanSnap Upgrade

Бренд: Fujitsu Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды