background image

 

 

7.0  Knife Installation/Changing 

 
 

 

15

 

7.0 Knife Installation/Changing 

  Changing knives can be very dangerous unless safety precautions are 

observed and extreme care is taken when handling knives. 
 

 

Make sure knife lifters are used properly, see instructions following. 

 

Keep handling of unprotected knives to an absolute minimum. 

 

Clear off cutter table before removing knife. 

 

Have scabbard nearby and insert knife immediately. 

 

Warn people of any unprotected knife.  

 

Knife changing is a ONE PERSON OPERATION.  Having more than one person trying to 
change knives invites accidents. 

 
 

 

Figure 11 – Spartan 150 Knife Change Accessories 

 
The knife changing equipment shown in Figure 11

 

is included with the machine.  The following 

instructions show how to remove and install a new or re-sharpened knife.  Read these instructions AT 
LEAST ONCE before attempting to actually change or install any blades. 
 

7.1 Knife Removal 

   Knives are always very sharp!  Be sure to keep the edge away from your 

body and keep other people out of the area while handling the blade.  Severe lacerations or 
dismemberment could result from careless handling procedures. 
 

1.  Lower the clamp to the table and remove the clamp handle and cutting lever handle. 

 

2.  Remove the top cover. 

 

Knife 

Scabbard 

5/32” 

T-Wrench 

Knife Lifter 
Assembly 

Содержание Challenge Spartan 150M























Отзывы: