Muton ValueJet VJ-1627MH Скачать руководство пользователя страница 45

Страница: 45 / 56

Sleep Mode

Installation of the ValueJet Status Monitor

Sleep Mode

When you are not using the printer, always leave the power on and put the printer into the sleep mode while not in use. If you

do not put the printer into the sleep mode, the ink inside the printer could settle out and/or coagulate, causing poor image

quality or printer failure.

Make sure to follow the instructions on the operation panel to perform daily maintenance.

If you set the printer’s sleep mode, the printer performs the following operation.

• Ink circulation (every 24 hours).

• “Little Charge” (once a week).

Important!

To leave the printer in sleep mode for seven days or more, perform followings once a week:

• Check the ink level and replace the relevant ink cartridge if “Ink Low” is displayed.

• Agitate the ink cartridges.

If the printer is not in use for more than two weeks, perform “Long Storage”.

Steps

[1]

Make sure that the printer’s operating condition is as follows:

• The front cover and the maintenance cover are closed.

• Media is removed from the printer.

• The remaining ink level is sufficient.

• The waste ink tank has enough space.

Important!

If you are going to use the sleep mode for a prolonged period of time, first empty the waste ink tank, as follows.

[2]

Prepare items required for daily maintenance.

Daily Maintenance Sheet for VJ-1627MH

[3]

Press the [Menu] key.

[4]

Press the [>] key.

[5]

Press the [Enter] key.

[6]

Press the [Enter] key.

Sleep Mode

Press!

Menu 1:

Sleep Mode >

Sleep Mode :

Start

Start Sleep Mode ?

Содержание ValueJet VJ-1627MH

























































Результаты поиска

Содержание ValueJet VJ-1627MH

Отзывы:

Похожие инструкции для ValueJet VJ-1627MH

Бренды по названию

Популярные бренды

Muton ValueJet VJ-1627MH, Руководство для стартапов

Результаты поиска

Содержание ValueJet VJ-1627MH

Отзывы:

Похожие инструкции для ValueJet VJ-1627MH

Бренды по названию

Популярные бренды