MUTOH VJ-628 ValueJet Скачать руководство пользователя страница 62

Страница: 62 / 80

62 Transporting

Transporting and long-term storage

Please refer to this section when transporting or storing this product for a long time.

When transporting this product, it is necessary to wash inside with cleaning cartridge, discharge waste ink and fixate the print

head with packaging material. If transported as it is, it can cause ink leakage and damage to the print head.

When it is used again, conduct reinstallation work and initial charging.

Transporting

Important!

• When moving this product, always empty the waste ink tank even if it is for a short distance.

If ink splashes inside the waste ink tank while being moved, it can cause damage.

• Do not tilt, set against something or place this product upside down.

Otherwise the ink may leak or the handling mentioned above may cause abnormality.

Head cleanining and discharging waste ink

[1]

Display the Printing Preferences screen of printer driver.

"Displaying the Printing Preferences screen of printer driver" on page 8

[2]

Click the [Maintenance] tab under the [Utility] tab.

[3]

Click [Long Store]

• The VSM remote panel opens.

Note

• VSM can be launched directly.

"Launching VSM" on page 9

Transporting and long-term storage

Содержание VJ-628 ValueJet

















































































Результаты поиска

Содержание VJ-628 ValueJet

Отзывы:

Бренды по названию

Популярные бренды

MUTOH VJ-628 ValueJet, Руководство по эксплуатации

Результаты поиска

Содержание VJ-628 ValueJet

Отзывы:

Бренды по названию

Популярные бренды