MUTOH VJ-626UF Скачать руководство пользователя

Страница: 77 / 144

Set 3: Initial Settings 77

Initial 3: Remain Ink

Selects how the remaining ink amount will be displayed.

Setting values

Remaining ink icons will not be displayed.
Slot numbers and remaining ink will be
displayed in numerals.

Remaining ink icons will be displayed.
This is the default setting.

Initial 4: IP Address

Sets the IP address of the printer.

• Use the [+] key to increase a setting value.

• Use the [ - ] key to decrease a setting value.

• Press the [Enter] key to confirm your input for a value. The cursor will move on

to the next setting value.

• Confirm your input for each value.

Setting values

0.0.0.0 to <192.168.1.253> to
255.255.255.255
<> indicates the default setting.

Initial 5:Subnet Mask

Sets the subnet mask of the printer.

• Use the [+] key to increase a setting value.

• Use the [ - ] key to decrease a setting value.

• Press the [Enter] key to confirm your input for a value. The cursor will move on

to the next setting value.

• Confirm your input for each value.

Setting values

0.0.0.0 to <255.255.255.0> to
255.255.255.255
<> indicates the default setting.

Initial3 :

Remain Ink

Remain Ink :

Off

Remain Ink :

Initial4 :

IP Address

IP :

192. 168. 1. 253

Initial5 :

Subnet Mask

MASK :

255. 255. 255. 0

Содержание VJ-626UF

















































































































































Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды

MUTOH VJ-626UF, Руководство по эксплуатации

Результаты поиска

Содержание VJ-626UF

Отзывы:

Похожие инструкции для VJ-626UF

Бренды по названию

Популярные бренды