MUTOH ValueJet VJ-1624WX Скачать руководство пользователя | Manualshive

Страница: 294 / 358

background image

6 Maintenance

VJ-1624X/1624WX/1924WX OPERATION MANUAL

294

6.2 Cleaning the printer

6.2

Cleaning the printer

Periodic (every month) cleaning is necessary to use the printer in good condition.

WARNING

• Do not insert or drop metal or flammable objects into the printer through openings

such as a vent.
It could lead to an electric shock or fire.

• If foreign substances or liquids such as water entered the printer, do not use the

printer as it is.
It could lead to an electric shock or fire.
Immediately turn OFF the power switch, disconnect the power plug from the electric
socket, and contact your local MUTOH dealer.

CAUTION

• When cleaning the outer case and inside of the printer, be sure to turn OFF the

power and disconnect Power plug.

• Do not use volatile solvents such as thinner, benzene, or alcohol.

These solvents may cause damage to the paint.

• Make sure that no moisture enters the printer.

The electric circuit inside the printer may be short-circuited.

• Never open covers attached using screws under any circumstances.

This may cause an electric shock or a malfunction.

This section describes how to clean each part of the printer.

«
...
292
293
294
295
296
...
»

Содержание ValueJet VJ-1624WX







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ValueJet VJ-1624WX

Бренд: Samsung Страницы: 165

Inkjet SCX-1150F

Бренд: Samsung Страницы: 66

Бренд: Samsung Страницы: 319

Бренд: Oki Страницы: 154

Бренд: Oki Страницы: 121

Бренд: Oki Страницы: 96

Бренд: SPRT Страницы: 13

Бренд: Xerox Страницы: 214

Бренд: Cardco Страницы: 28

Falcon Outdoor 46

Бренд: MUTOH Страницы: 333

Magicard Opera 100

Бренд: Ultra electronics Страницы: 2

Бренд: Paaasonic Страницы: 14

ColourLaser 21 Series

Бренд: Xante Страницы: 32

Бренд: HanBot Страницы: 13

Бренд: IBM Страницы: 2

Бренд: AGFA Страницы: 168

Бренд: Nova Страницы: 3

Бренд: AMT Datasouth Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды