MUTOH ValueJet VJ-1624WX Скачать руководство пользователя | Manualshive

Страница: 21 / 358

background image

VJ-1624X/1624WX/1924WX OPERATION MANUAL

1 Safety instructions

1.3 Warning labels

21

1.3

Warning labels

This section explains the handling of warning labels, their pasting locations and types.
Warning labels are attached to parts of the printer that need special caution.
Understand the locations and the descriptions of the danger associated with each label before operating
the printer.

1.3.1

Handling the warning labels

When handling the warning labels, be careful with the following points.

NOTE

• Check whether all the warning labels can be read.

If the letters or illustrations on the label are not clear, remove the dirt from the label.

• Use cloth, water and mild detergent for removing dirt from the warning labels.

Avoid organic solvents and gasoline.

• Replace the labels if they are damaged, lost or illegible.

If the warning labels have to be replaced, contact your local MUTOH dealer.

«
...
19
20
21
22
23
...
»

Содержание ValueJet VJ-1624WX







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ValueJet VJ-1624WX

Бренд: TallyGenicom Страницы: 310

Бренд: TallyGenicom Страницы: 330

Бренд: Oki Страницы: 222

Бренд: Oki Страницы: 4

Бренд: Oki Страницы: 160

Бренд: Tally Страницы: 28

Accel-a-Writer 8200

Бренд: Xante Страницы: 12

apeosport 550 I

Бренд: Xerox Страницы: 160

Бренд: RAYSHAPE Страницы: 41

Бренд: Brother Страницы: 378

Бренд: Brother Страницы: 107

Бренд: Oce Страницы: 22

VarioPrint 6000 Plus Line

Бренд: Oce Страницы: 102

Бренд: Oce Страницы: 200

Бренд: Evolis Страницы: 59

Бренд: Evolis Страницы: 37

Бренд: Evolis Страницы: 47

Бренд: Custom Audio Electronics Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды