MUTOH ValueJet VJ-1624WX Скачать руководство пользователя

Страница: 197 / 358

VJ-1624X/1624WX/1924WX OPERATION MANUAL

4 Handling the printer

4.4 Operating from Operation panel

197

4.4.7

Starting printing during warming up (VJ-1624X only)

You can start printing while the printer is warming up, even though the heater temperature has not
reached the set temperature.

NOTE

• Even when you start printing during warming up, warming up continues until the remperature

reaches the set temperature.

• If you start printing during warming up, print quality will not be guaranteed.

1. Confirm that the printer is warming up.

•

"Warming Up" is displayed on Operation panel.

2. Print data will be sent.

•

"Warming Up" and "Skip ->E" is displayed on Operation panel.

CAUTION

• While "Warming Up" is displayed, do not touch Platen and Media guide.

You could burn yourself.

3. To start printing during warming up, press the [Enter] key on Operation panel.

•

The printer starts printing.

Содержание ValueJet VJ-1624WX







































































































































































































































































































































































Результаты поиска

Содержание ValueJet VJ-1624WX

Отзывы:

Похожие инструкции для ValueJet VJ-1624WX

Бренды по названию

Популярные бренды

MUTOH ValueJet VJ-1624WX, Руководство по эксплуатации

Результаты поиска

Содержание ValueJet VJ-1624WX

Отзывы:

Похожие инструкции для ValueJet VJ-1624WX

Бренды по названию

Популярные бренды