MUTOH ValueJet VJ-1624WX Скачать руководство пользователя страница 186

Страница: 186 / 358

4 Handling the printer

VJ-1624X/1624WX/1924WX OPERATION MANUAL

186

4.3 Menu setups on Operation panel

4.3

Menu setups on Operation panel

4.3.1

Menu setup procedure

Follow the procedure below to configure each setup menu.

1. Confirm that Operation panel is Normal.

2. Press the [Menu] key on Operation panel.

•

"Menu1: Setup>" is displayed on Operation panel.

3. Press the [+] key or [-] key on Operation panel to select a setup item and press the [>] key.

•

The settings will be confirmed.

•

When setup items have a submenu, the display shifts to the next menu.

NOTE

• When a setup item has a submenu, ">" is displayed on the right end of LCD monitor of Operation

panel.

• For the general outline of each setup item, refer to

4.3.2 Panel setup menu overview

Содержание ValueJet VJ-1624WX







































































































































































































































































































































































Результаты поиска

Содержание ValueJet VJ-1624WX

Отзывы:

MUTOH ValueJet VJ-1624WX, Руководство по эксплуатации, Страница: 186 / 358

Результаты поиска

Содержание ValueJet VJ-1624WX

Отзывы: