(1) General
Plug connector only under zero voltage (Insert / Remove).
The compact power supply unit is potted and suitable for harsh environmental conditions.
Only for use in pollution degree 2 environment (Controlled Environment).
(3) Features
[1]
Input terminal:
3-pin 7/8" receptacle male with external threads.
To tighten the mating connector use Murrelektronik 7/8" 1.5 Nm torque wrench set AF 22:
Art. No.: 7000-99104-0000000 with correct 7/8" wrench.
[2]
IO-Link terminal:
4-pin M12 receptacle male with external threads.
To tighten the mating connector use Murrelektronik M12 0.6 Nm torque wrench set AF 13:
Art. No.: 7000-99102-0000000.
[3]
Output terminal:
5-pin 7/8" receptacle female with internal threads.
To tighten the mating connector use Murrelektronik 7/8" 1.5 Nm torque wrench set AF 22:
Art. No.: 7000-99104-0000000 with correct 7/8" wrench.
[4]
DI/DO, LED is yellow / IO-Link, LED is blinking green.
[5]
Input power OK, LED is green.
[6]
Channel is selected when the LED is yellow.
[7]
The channel selector switch. You can turn the output ON or OFF with this switch.
[8]
Channel output is ON / LED is green.
- channel output load is 90% or more from setting current / blinking green LED.
- channel output is OFF / LED is red.
- overcurrent trip / LED is blinking red.
[9]
7-segment display shows the current limit value. When changing the current limit, the dot will
blink.
[10]
Select / set switch.
(4) Functionality
Checking current limit:
Press select switch
[10]
, channel U
S
has yellow LED ON
[6]
and 7-segment display show current
limit, press select switch
[10]
again and channel U
A
has yellow LED ON
[6]
and 7-segment
display show current limit. After checking limits, wait few seconds and channel LED
[6]
will go
OFF.
Adjusting the current limit:
REMARK!
Current setting only when outputs are in OFF mode (automatic).
1. Press select switch
[10]
for 3 seconds.
2. Both channels have yellow LED blinking
[6]
.
3. Select the channel with the channel selector switch
[7]
.
4. 7-segment display
[9]
shows the current value of the current channel and the dot in the display
is blinking.
5. Use select switch
[10]
to set current limit for selected channel (1A -> 2A -> 3A...).
6. After you have set current limit, press channel select switch
[7]
or wait few seconds.
7. To get the channel active, press the switch
[7]
and then channel output LED
[8]
will change
from red to green.
(5) Location
The power supply is cooled by natural convection. Protection degree of the housing is IP67.
Switch-Mode Power Supply for both inside and outside of the cabinet with 7/8’’ input-, 7/8’’ output
connector and M12 IO-Link connector.
(6) Mounting [11]
- front mounting with 6 x M4 screws.
- side mounting with 4 x M4 screws.
Vertical and horizontal mounting is possible. Not for direct sunlight.
(7) Switching on
Check input and output connectors and their connection before switching power on. Current limit
for different outputs U
5
=2 A and U
)
=8 A (factory default).
(8) Loading capacity
The nominal current for one output is 8 A and the total current for both outputs is 10 A. If total
output current goes over 10 A for over 4 seconds, output U
)
will be switched off.
We reserve the right to change this specification.
Product of the Emparro67 series
D-71570 Oppenweiler
Murrelektronik GmbH
Falkenstraße 3
In order to take the best advantage of
the features that this power supply has
to offer and to ensure long term
reliability for your equipment, please
read this manual carefully before
installation and use. It should be
retained for future reference.
Emparro67 10-100-240/24 2xMICO 7/8" IOL
Art. No. 85676
INSTALLATION INSTRUCTIONS
SELECT
<SET>
INPUT OK
IO
-Link
OUT 2 / U
A
OUT 1 / U
S
SELECT
<SET>
OUTPUTS
IO
-Link
DI / DO
1
2
3
11
5
6
7
8
10
4
9
6
7
8
MICO OUTPUTS: 2 x 24 VDC, 240 W, SELV
Emparro67 Hybrid 10-100-240/24 2x MICO 7/8'' IOL
ART. NO. 85676
CAUTION
Read instruction manual before installation and use.
INPUT:
100 - 240 VAC ± 10%
50 - 60 Hz ± 6%
2.7 - 1.2 A
MADE IN CZECH REPUBLIC
DESIGNED IN FINLAND
45012 - 1.00 - 1.00
IP67
100 - 240 VDC - 10% / + 55%
2.7 - 1.1 A
PF 0.95
Surrounding air temperature
-25°C ... +80°C >50°C DERATING
Tc: max. +80°C
Max. 8 A / OUTPUT
Max. 10 A / TOTAL
Operator access area max. +40°C
Tc
INPUT
N / DC-
L / DC+
D-71570 Oppenweiler
Emparr
o
Hybrid
Falkenstraße 3
Murrelektronik GmbH
®
SELECT
<SET>
INPUT OK
IO
-Link
OUT 2 / U
A
OUT 1 / U
S
SELECT
<SET>
OUTPUTS
IO
-Link
DI / DO
IP67
IND.CONT.EQ.
61RM
IND.CONT.EQ.
61RM
N / DC-
L / DC+
+
+
(Us)
(Us)
(U )
A
(U )
A
1
4
3
2
1 24 V
2 DI/DO
3 0 V
4 IO link
(2) Technical specification, Art. No. 85676
V1.1
Nominal voltage
100 - 240 VAC
Input voltage range
90 - 265 VAC
Power distribution systems
TN, TT, IT mains
Nominal frequency
50 - 60 Hz ±6%
Input current, I
nom.
2,7 A
rms
/ 115 VAC - 1,2 A
rms
/ 230 VAC
Inrush current
< 5,9 A / 230 VAC after 1 ms
Efficiency, typ.
91,6% / 115 VAC - 92,8% / 230 VAC
Power factor, typ.
0,99 / 115 VAC - 0,88 / 230 VAC
Output power
240 W
Power losses
< 18,7 W with 230 VAC
No-load power losses
< 3,7 W with 230 VAC
Internal fuse F1:
6,3 A (T)
External fuse max.
20 A in building installations. Circuit
breaker type B or C recommended.
Safety class
1
Output voltage
24 VDC
Output voltage, adjustable via the IO-Link
24 - 28 VDC
Static regulation accuracy
+/- 1%
Dynamic regulation accuracy typ.
0->100%->5%; <2ms:5%, >2ms: 2%
Start-up time
< 0,6 s
Hold up time of the output, typ.
> 20 ms
Output ripple
< 10 mV
rms
Overloading / temperature protection
Yes
Relative humidity
4 - 100%
Maximum surrounding air temperature
-25°C - +80°C (> +50°C derating)
Storage temperature
-40°C - +85°C
Protection class, case, EN 60529
IP67
Dimensions W x H x D; Weight
217 x 110 x 53 mm; 1,9 kg
www.comoso.com
