background image

 

 

A151.8-VR

Page 11 of 11

Date: 

11/10/2020

7021-024-001

MURDOCK  MFG.  • 

15125  Proctor  Avenue  •  City  of  Industry,  CA  91746  USA 

Phone  800-453-7465  or  626-333-2543  •  Fax  626-855-4860  •  www.murdockmfg.com

Member of

Repairs must be made with Murdock Manufacturing parts only. Please order through your local 
representative or distributor. The phone number to locate your local representative is 1.800.591.9360. 

VANDAL RESISTANT DRINKING FOUNTAIN PARTS BREAKDOWN DRAWING                         

CONTEMPORARY WATER COOLERS

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

 DRINKING FOUNTAINS

 

  

 

NOTE:

** Flow Restrictor Only Available

    With Low Flow Bubbler.

ITEM # PART NUMBER DESCRIPTION

ITEM # PART NUMBER DESCRIPTION

1

7000-005-199

Drain Adapter

9

7003-193-000

Spring, Pushbutton Return

2

0116-016-000

#10-32 x 3/8" Phillips Truss Head Screw

10

7003-196-199

Pushbutton, Chrome 

3

7000-006-000

Flat Drain Adapter Gasket

11

7003-197-199

Escutcheon, Chrome

4

7000-015-000

1-1/4" OD P-Trap

12

0161-062-000

#6-32 x 1/2" Phillips, Flat Head Screw 

5

0152-010-000

#10-32 x 1" Hex Flat Head Screw

13

0124-055-000

#8 x 3/4" Phillips, Round Head Screw

6A

7000-012-001

Stainless Steel Bubbler Assembly

14

7003-198-199

Mounting Sleeve

6B

7000-099-002

Flexible Gray Bubbler Assembly

15

7003-095-001

Valve Body Sub Assembly

7

1895-123-000

1/4" x 3/8" OD Tube Union Push-In

16

7003-093-001

Flow Restrictor - Low-Flow Bubbler Only

8

7003-195-000

Spring, Overtravel

1

2

3

4

5

6A

6B

9

10

11

8

16

15

14

13

12

7

Содержание A151.8-VR Series












Отзывы: