Multistack MS010XC Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 40

Multistack MS010XC Скачать руководство пользователя страница 26

26

10. The ground bar must be drilled, then attached to the module

ground lug.

11. Reinstall the buss duct and isolation switch covers. Install

the main power connectors as shown.

NOTE: IT IS THE ELECTRICIAN’S RESPONSIBILITY TO CONNECT

MAIN POWER TO THIS CONNECTOR.

12. Install the power phase monitor as shown. When correctly

installed the lettering on the power phase monitor is inverted.

Wires are run to the normally open contact of the power phase

monitor and connect to the master control.

DANGER:

To avoid the risk of electrical shock, personal injury or death, disconnect all electrical power to the unit before performing any maintenance

or service. The unit may have more than one electrical power supply. Assume all electrical wires are live, energized wires. Use lockout/tagouts.

Module wiring connections to the power junction

box must be completed by a qualified electrician.

NOTE:

Be sure to replace all protective covers

after completing wiring connections.

On water cooled chillers with single point power, optional wire whips may be ordered and

substituted for the standard buss bar. The conduit, wiring and junction box are shipped as part

of the loose parts package. The wire and conduit are then connected to the junction box as the

modules are installed. Each wire and circuit breaker is marked for correct connection.

Single Point Power

Each wire and circuit breaker is marked for correct

connection.

«
...
24
25
26
27
28
...
»

Содержание MS010XC









































Отзывы:

Нет отзывов