background image

page 48 — Sg1400C3 STudio generaTor • operaTion manual — rev. #0 (10/05/11) 

driving CondiTionS

When towing a trailer, you will have decreased acceleration, 

increased stopping distance, and increased turning radius 

(which means you must make wider turns to keep from 

hitting curbs, vehicles, and anything else that is on the 

inside corner). In addition, you will need a longer distance 

to pass, due to slower acceleration and increased length.

 

„

Be alert for slippery conditions. You are more likely to be 

affected by slippery road surfaces when driving a tow 

vehicle with a trailer, than driving a tow vehicle without 

a trailer.

 

„

Check rearview mirrors frequently to observe the trailer 

and traffi c.

 

„

never drive faster than what is safe.

Coupling To THe ToW veHiCle

Follow  all  of  the  safety  precautions  and  instructions  in 

this manual to ensure safety of persons, equipment, and 

satisfactory life of the trailer. Always use an adequate tow 

vehicle  and  hitch.  If  the  vehicle  or  hitch  is  not  properly 

selected and matched to the Gross Vehicle Weight Rating 

(GVWR) of your trailer, you can cause an accident that 

could lead to death or serious injury.  
If you already have a tow vehicle, know your vehicle tow 

rating and make certain the trailer’s rated capacity is less 

than or equal to the tow vehicle’s rated towing capacity. If 

you already have (or plan to buy) a trailer, make certain 

that the tow rating of the tow vehicle is equal to or greater 

than that of the trailer.
The trailer VIN tag contains the critical safetyinformation 

  Warning

Driving too fast for severe road conditions can result in 

loss of control and cause death or serious injury.
Decrease your speed as road, weather, and lighting 

conditions deteriorate.
Always check for local trailer tow speed limits in your 

area.

  Warning

Do not transport people on the trailer. The transport of 

people puts their lives at risk and may be illegal.

for the use of your trailer. Again, be sure your hitch and tow 

vehicle are rated for the Gross Vehicle Weight Rating of 

your trailer.

  Warning

Proper selection and condition of the coupler and hitch 

are  essential  to  safely  towing  your  trailer.  A  loss  of 

coupling may result in death or serious injury.
•  Be sure the hitch load rating is equal to or greater 

than the load rating of the coupler.

•  Be sure the hitch size matches the coupler size.
•  Observe  the  hitch  for  wear,  corrosion  and  cracks 

before coupling. Replace worn, corroded or cracked 

hitch components before coupling the trailer to the 

tow vehicle.

•  Be  sure  the  hitch  components  are  tight  before 

coupling the trailer to the tow vehicle.

  Warning

An  improperly  coupled  trailer  can  result  in  death  or 

serious injury.
do noT move the trailer until:
•  The coupler is secured and locked to hitch.
•  The safety chains are secured to the tow vehicle.
•  The trailer jack(s) are fully retracted.
do noT tow the trailer on the road until:
•  Tires and wheels are checked.
•  The trailer brakes are checked.
•  The  breakaway  switch  is  connected  to  the  tow 

vehicle.

•  The load is secured to the trailer.
•  The trailer lights are connected and checked.

  Warning

Use of a hitch with a load rating less than the load rating 

of the trailer can result in loss of control and may lead 

to death or serious injury.
Use of a tow vehicle with a towing capacity less than 

the load rating of the trailer can result in loss of control, 

and may lead to death or serious injury.
Be sure your hitch and tow vehicle are rated for the 

Gross Vehicle Weight Rating of your trailer.

traiLEr GuiDELinES

Содержание MQ POWER SG1400C3































































Отзывы: