MULTILIFT XR S Скачать руководство пользователя страница 79

Страница: 79 / 210

XR21S59 CHU

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

FLAT

TIP

ISO

STO

MAN

URB

Loading of rear heavy flatrack/body

A flatrack/body loaded more heavily at the rear end can cause the truck front

wheels to be lifted of the ground. Be extra cautious when this happens.

When the flatrack/body is on rear rollers, move the hook arm forward before

lowering the middle frame on the sub-frame. Otherwise there is a danger of

the flatrack/body becoming loose from the hook.

Note:

When the middle frame is coming down to floating

area, there is a risk that the rear frame jumps up. If this

happens the system stops and d012 can be seen in the

display. Move the sliding arm slowly more forwards or

backwards to get the rear frame down.

Unloading of a rear heavy flatrack/body

When unloading a long or rear heavy flatrack/body to the ground, move the

hook arm forward before the flatrack/body touches the ground. Otherwise

there is a danger of the flatrack/body becoming loose from the hook.

Loading of a front heavy container

When loading a too front heavy container it might happen, that the equipment

is not strong enough to carry out the loading, although the total weight of the

container and the load would not exceed the maximum allowed. In this case

move the load closer to the centre of the container, if possible.

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды