MULTILIFT XR S Скачать руководство пользователя страница 31

Страница: 31 / 210

XR21S59 CHU

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Safety facilities of the XR S hooklift equipment

To increase safety, the control system has safety features to prevent incorrect movements

of the body so that the load can be kept under control.

The hydraulic cylinders are provided with load holding valves that ensure a controlled

movement of the XR S equipment. In addition these valves serve as a safety feature in

case of the failure of hydraulic hoses.

The following functions have safety features:

• Hydraulic body locks cannot be opened during tipping.

• Hydraulic body locks cannot be closed during loading and unloading.

• If the body locks are closed, it is not possible to move the hook arm.

• Moving the hook arm is not possible during tipping.

• When tipping, the rear frame and the middle frame are locked together by

the tipping lock. The lock operates mechanically.

• Tipping action cannot be initiated if the hydraulic body locks are open.

• The hook arm stops in two positions:

• Fully forward - this is when carrying an ISO container OR

during the stowing/unstowing operation = CONTAINER HOME POSITION.

• Approx 350 mm rearwards - this is when carrying a flatrack/body OR

when empty = FLATRACK HOME POSITION.

Содержание XR S



















































































































































































































Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды

MULTILIFT XR S, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание XR S

Отзывы:

Похожие инструкции для XR S

Бренды по названию

Популярные бренды