MULTILIFT Ultima S Flex Скачать руководство пользователя страница 163

Страница: 163 / 196

163

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

Service Manual

>>>

Exit

FAULT FINDING

MULTILIFT PLC - Diagnostic Codes

The diacnostic codes of Multilift PLC can be seen on the display of control unit and on the

service display.

Press the top left button (

locks closed

) to exit from the sub

level menu.

Text “

tESt

” will be shown.

Press both top buttons for 5 seconds to exit the software and

return back to normal operation.

The text “

OFF

” will be shown for a couple of seconds in the

display.

The backlight illumination will dim after 30 seconds of inactive period and light

up when joystick is moved or any button pressed.

If both “

” and “

” are set to same value, there is no difference in the

brightness.

Press

5 s

Содержание Ultima S Flex





































































































































































































Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды

MULTILIFT Ultima S Flex, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды