MULTILIFT Ultima S Flex Скачать руководство пользователя страница 114

Страница: 114 / 196

114

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

User Manual

Additional hydraulics

Auxiliary equipment connected to the Ultima´s own hydraulics, is controlled by the additional

hydraulic switch (push button), for example, tail gate, sand spreader, etc.

Additional hydraulics can be changed to continuous operation in two ways, depending

on settings of the control system:

1. (standard setting) by pushing simultaneously the button

additional hydraulics on

and the button

body locks closed

for 2 seconds.

2. (alternative setting) by pushing the button

additional hydraulics on

for 2 seconds.

When switching on, the display will show text ”

” for a moment.

Switching off can be obtained by pressing the

stop the operation of additional hydraulics

and the display will then show text “

OFF

”.

Switching on the function for continuous operation by radio control (2GRC or 2GMR) is

blocked up for safety reasons.

2 sec

Function

Additional

hydraulics on

Switch the

additional

hydraulics to

continuous

operation mode

”On” appears for

approx. 2 seconds

LED starts blinking

LED is

blinking when

the additional

hydraulics is

in continuous

operation

mode

Additional

hydraulics off

”OFF” appears

for approx. 2

seconds

LED stops

blinking

Display

and LEDs

2GCC

Button

Содержание Ultima S Flex





































































































































































































Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды

MULTILIFT Ultima S Flex, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды