MTX MTX-3G-JAVA-IoT Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 128

background image

76

MTX-Java-IoT | 2018/2

MTX © by MATRIX ELECTRONICA S.L.U.

SUPPORT:

[email protected] |

SALES:

[email protected] |

mtxm2m.com

12. Real Time Clock

The GSM module attached to MTX-Java-IoT modems contains a real time clock (RTC) to maintain accurate

timekeeping and to enable you to “time stamp” messages.
This RTC is supplied by a separate voltage regulator which is also active when the MTX-Java-IoT is in

power down mode and the power supply VIN is available. An alarm function is provided that allows the

MTX-Java-IoT to wake up in Airplane mode without logging onto the GSM/UMTS network.
The MTX-Java-IoT modems also accommodate an independent super-cap inside to maintain the date

and time of the RTC when the power supply is disconnected. This super-cap will be charged when power

supply is present again.

«
...
74
75
76
77
78
...
»

Содержание MTX-3G-JAVA-IoT

































































































































Отзывы:

Нет отзывов

Похожие инструкции для MTX-3G-JAVA-IoT

Бренд: USR IOT Страницы: 52

Бренд: Kathrein Страницы: 16

Бренд: OUMAN Страницы: 4

Бренд: Aztech Страницы: 16

Premium Motorola 3347

Бренд: Motorola Страницы: 11

Бренд: Motorola Страницы: 16

SURFboard SB5102

Бренд: Motorola Страницы: 47

SURFboard SB4220 Series

Бренд: Motorola Страницы: 66

SURFboard SB5102

Бренд: Motorola Страницы: 2

SURFboard SBV5122

Бренд: Motorola Страницы: 24

SURFboard SB6121

Бренд: Motorola Страницы: 27

Бренд: Motorola Страницы: 36

SBV5322 SURFBOARD DIGITAL VOICE MODEM - annexe 3

Бренд: Motorola Страницы: 43

SBV5322 SURFBOARD DIGITAL VOICE MODEM - annexe 1

Бренд: Motorola Страницы: 43

SBV5322 SURFBOARD DIGITAL VOICE MODEM - annexe 2

Бренд: Motorola Страницы: 43

SURFboard SB5102

Бренд: Motorola Страницы: 2

SB5100 - SURFboard - 38 Mbps Cable Modem

Бренд: Motorola Страницы: 74

SB5100 - SURFboard - 38 Mbps Cable Modem

Бренд: Motorola Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды