MTU M015710/04E Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 196

MTU M015710/04E Скачать руководство пользователя страница 63

5 Maintenance

5.1 Maintenance task reference table [QL1]

The maintenance tasks and intervals for this product are defined in the Maintenance Schedule. The

Maintenance Schedule is a stand-alone publication.
The task numbers in this table provide reference to the maintenance tasks specified in the Maintenance

Schedule.

Task

Option

Maintenance tasks

W0500

Check engine oil level.

W0501

Visually inspect engine for leaks and general condition. (→ Page 72)

W0502

X

Check intercooler drain(s).

W0503

Check signal ring position of service indicator on air fil‐

ter.

W0505

Check relief bores of water pump(s).

W0506

Check engine for abnormal running noises, exhaust col‐

or and vibrations.

W0507

X

Drain water and contaminants from fuel prefilter.

W0508

X

Check reading on differential pressure gage of fuel pre‐

filter.

W0534

Carry out test run, minimum duration: until steady-state

temperature is reached, no less than 1/3 load (monthly).

W1001

Replace fuel filter or fuel filter element.

W1005

Replace air filter.

W1006

Replace fuel injectors.

W1008

Replace engine oil filter when changing engine oil, or

when the interval (years) is reached, at the latest.

W1009

X

Check layer thickness of the oil residue, clean out and

replace filter sleeve.

W1011

Perform endoscopic examination.

W1046

Crankcase breather: Replace filter or filter element.

W1207

Check and adjust valve clearance. Attention!First adjust‐

ment after 1,000 operating hours.

W1241

Check condition of belt drive and replace if necessary;

adjust belt tension.

W1463

Check general condition of engine mounting (visual in‐

spection).

W1714

X

Check and clean oil indicator filter.

Table 1: Maintenance task reference table [QL1]

78 | Maintenance | M015710/04E 2012-09

TIM-ID: 0000022705 - 003

«
...
61
62
63
64
65
...
»

Содержание M015710/04E





































































































































































































Отзывы:

Нет отзывов