MTU M015710/04E Скачать руководство пользователя страница 13

Страница: 13 / 196

3.2 12 V 4000 Gx3 engine data: Continuous operation, variable

3B, optimized fuel consumption

Explanation

Abbrevia‐

tion

Meaning

Ref. value: Continuous power

Ref. value: Fuel stop power

Design value

Guaranteed value

Guideline value

Limit value, up to which the engine can be operated, without change (e.g. of power set‐

tings).

Not yet defined value

Not applicable

Applicable

Reference conditions

Engine model

12V4000

G23

12V4000

G23R

12V4000

G43

12V4000

G63

12V4000

G83

Application group

Intake air temperature

°C

Charge-air coolant tempera‐

ture

°C

Raw water inlet temperature

°C

Barometric pressure

mbar

1000

Site altitude above sea level

100

Power-related data (power ratings are net brake power to ISO 3046)

Number of cylinders

Rated engine speed

A rpm

1500

1800

1500

1800

Continuous power ISO 3046

(10% overload capability, de‐

sign power DIN 6280, ISO

8528)

A kW

1420

1205

1520

1575

1736

General conditions (for maximum power)

Number of cylinders

Intake depression (new filter) A mbar

Intake depression, max.

L mbar

Exhaust overpressure

A mbar

Exhaust overpressure, max. L mbar

28 | Technical Data | M015710/04E 2012-09

TIM-ID: 0000002981 - 002

Содержание M015710/04E





































































































































































































Результаты поиска

Содержание M015710/04E

Отзывы:

MTU M015710/04E, Руководство по эксплуатации, Страница: 13 / 196

Результаты поиска

Содержание M015710/04E

Отзывы: