MTU 8V4000M*3 series Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 260

background image

8.4 Crankcase Breather

8.4.1 Crankcase breather – Oil mist fine separator replacement

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Engine oil
Oil mist fine separator

(→ Spare Parts Catalog)

O-ring

(→ Spare Parts Catalog)

WARNING

Oil is hot.
Oil can contain residue/substances which are harmful to health.
Risk of injury and poisoning!
• Allow the product to cool to below 50 °C before beginning work.
• Wear protective clothing, protective gloves and goggles/safety mask.
• Avoid contact with skin.
• Do not inhale oil vapor.

Replacing oil mist fine separator

1.

Remove screws (1) and washer (2) and take
off together with plug (6).

2.

Remove both retainers (3).

3.

Replace oil mist fine separator (4).

4.

Replace O-ring (5) as necessary.

5.

Replace other oil mist fine separators in the
same way.

148 | Crankcase Breather | MS15034/00E 2018-08

TIM-ID: 0000065663 - 003

«
...
148
149
150
151
152
...
»

Содержание 8V4000M*3 series





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8V4000M*3 series

Бренд: VEM Страницы: 27

Бренд: FeiaoModel Страницы: 7

Бренд: Perkins Страницы: 92

Бренд: MTU Страницы: 153

FIFTY-FIVE - REV1 11-2007

Бренд: NOVAK Страницы: 2

LYCOMING 200-6XL Series

Бренд: E-MAG Страницы: 30

1550 STERNDRIVE

Бренд: Mercury Racing Страницы: 75

Бренд: Moons' Страницы: 28

Бренд: Brother Страницы: 76

Бренд: Brother Страницы: 112

Бренд: Brother Страницы: 22

Бренд: Iveco Motors Страницы: 60

Бренд: Iveco Страницы: 206

Бренд: Hyundai Seasall Страницы: 150

ARO AF1060 Series

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Ingersoll-Rand Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды