manualshive.com logo in svg

MTU 20V4000Bx4, Руководство по эксплуатации

Поделиться
Скачать
MTU 20V4000Bx4 Скачать руководство пользователя страница 213

8.7.3 Fuel cooler – Cleaning

Preconditions

☑

Engine is stopped and starting disabled.

☑

All fuel cooler power sources are disconnected.

WARNING

Hot components/surfaces.
Risk of burns!
• Allow the engine to cool down to below 50 °C before beginning work.
• Wear suitable protective equipment/thermal gloves.
• Avoid unprotected contact with hot surfaces.

WARNING

Fuels are combustible and explosive.
Risk of fire and explosion!
• Avoid open flames, electrical sparks and ignition sources.
• Do not smoke.
• Wear protective clothing, protective gloves, and safety glasses / facial protection.

WARNING

Liquid or gaseous media, e.g. fuel, are poisonous.
Escaping vapors of highly volatile media, e.g. fuel or ether.
Risk of fatal injury through swallowing; risk of poisoning through inhalation; irritation to eyes
and skin!
• Seek medical attention immediately; do not induce vomiting.
• Do not inhale vapors or mist.
• Wear protective clothing, protective gloves, and safety glasses.
• If contact is made with skin, wash off with water and soap.

WARNING

Compressed air gun ejects a jet of pressurized air.
Risk of injury to eyes and damage to hearing, risk of rupturing internal organs!
• Never direct air jet at people.
• Always wear safety goggles/face mask and hearing protection.

WARNING

Chemical substances in cleaners.
Risk of irritation and chemical burns!
• Always obey manufacturer's instructions for use.

NOTICE

Cleaning agents should not be left to take effect for too long.
Damage to components is possible!
• Observe manufacturer's instructions.

NOTICE

Inappropriate cleaning tool.
Risk of damage to component!
• Observe manufacturer's instructions.
• Use appropriate cleaning tool.

MS15039/01E 2018-11

| Fuel System | 211

TIM-ID: 0000081754 - 002

Содержание 20V4000Bx4

















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды