MTU 20V4000Bx4 Скачать руководство пользователя страница 185 | Manualshive

Страница: 185 / 304

background image

8.3 Crankcase Breather

8.3.1 Crankcase breather – Oil mist separator replacement

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Engine oil
Oil mist separator

(→ Spare Parts Catalog)

O-ring

(→ Spare Parts Catalog)

WARNING

Oil is hot.
Oil can contain residue/substances which are harmful to health.
Risk of injury and poisoning!
• Allow the product to cool to below 50 °C before beginning work.
• Wear protective clothing, protective gloves and goggles/safety mask.
• Avoid contact with skin.
• Do not inhale oil vapor.

Oil mist separator – Replace-
ment

1.

Remove screws (1) and take off together with
retainer (2).

2.

Replace oil mist separator (3).

3.

Replace O-ring (4) if necessary.

4.

Replace further oil mist separators in the
same way.

MS15039/01E 2018-11

| Crankcase Breather | 183

TIM-ID: 0000018590 - 010

«
...
183
184
185
186
187
...
»

Содержание 20V4000Bx4

















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 20V4000Bx4

Бренд: Tanaka Страницы: 7

Бренд: Lycoming Страницы: 155

DSC1-045-100 Series

Бренд: Baumuller Страницы: 116

Бренд: LONCIN Страницы: 27

Бренд: Honda Страницы: 16

Бренд: Honda Страницы: 30

Бренд: Honda Страницы: 48

Бренд: Honda Страницы: 80

Бренд: Volvo Penta Страницы: 122

Бренд: Agrimate Страницы: 32

Бренд: DLE Страницы: 4

Бренд: E-FLITE Страницы: 3

Power 25 Brushless Outrunner

Бренд: E-FLITE Страницы: 4

Бренд: Mitsubishi Страницы: 3

Бренд: Traxxas Страницы: 40

Бренд: CRRCpro Страницы: 8

Бренд: Yanmar Страницы: 394

Бренд: Nanni Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды