manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации, Страница: 255 / 305

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 255

8.22.2 Actuators – Visual inspection and test

Preconditions

☑

Engine is stopped and starting disabled.

WARNING

Actuation mechanism in the exhaust and intake area closes automatically.
Risk of crushing hands!
• To carry out the teach-in routine, keep clear of the safety zone of the actuation mechanism in the

intake and exhaust area.

• Switch off the operating voltage of the engine governor before starting the mechanical test.
• Wear protective goggles.

WARNING

Hot components/surfaces.
Risk of burns!
• Allow the engine to cool down to below 50 °C before beginning work.
• Wear suitable protective equipment/thermal gloves.
• Avoid unprotected contact with hot surfaces.

NOTICE

Carry out the calibration learning run for a functional check of the servomotor. Overwriting of stop val-
ues through already existing wear.
Exceeding of emission values and engine damage are possible!
• Only carry out the calibration learning run if the servomotor of the flap is connected to the ECU for

the first time or a coupling rod was been replaced.

Checking actuators visually

Note

Actuators must not be interchanged or exchanged from other engines - even for test purposes. Always use
new actuators.

Item

Findings

Measure

Corrugated pipe (1)

Damaged, holes or cracks.

Replace

Coolant connections (2, 3)

Traces of coolant leaks.

Replace

Output shaft (4)

Damaged

Replace

MS15041/03E 2018-08

| Accessories for (Electronic) Engine Governor / Control System  | 253

TIM-ID: 0000044543 - 007

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов