manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации, Страница: 188 / 305

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 188

8.9.2 Fuel prefilter with internal electrical priming pump – Draining

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Diesel fuel

WARNING

Fuels are combustible and explosive.
Risk of fire and explosion!
• Avoid open flames, electrical sparks and ignition sources.
• Do not smoke.
• Wear protective clothing, protective gloves, and safety glasses / facial protection.

Fuel prefilter – Draining

1.

Close shut-off valve in fuel supply line for fil-
ter A and B.

2.

Open threaded vent plug (1) of the filter that
should be drained.

3.

Open drain valve (2) and drain water and con-
taminates until clear fuel emerges.

4.

Close drain valve (2).

5.

Fill filter housing with clean fuel through the
vent plug opening.

6.

Tighten vent plug (1) by hand until it clicks.

7.

Open shut-off valve in fuel supply line for fil-
ter A and B.

186 | Fuel Filter | MS15041/03E 2018-08

TIM-ID: 0000082688 - 001

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов