manualshive.com logo in svg

MTU 12V4000C*5 series, Руководство по эксплуатации, Страница: 158 / 305

Поделиться
Скачать
MTU 12V4000C*5 series Скачать руководство пользователя страница 158

8.1.3 Engine – Test run

DANGER

Components are moving or rotating.
Risk of crushing, danger of parts of the body being caught or pulled in!
• Operate the engine at low load only. Keep clear of the danger zone of the engine.

WARNING

Exhaust gases are harmful to health and may cause cancer.
Risk of poisoning and suffocation!
• Keep the engine room well-ventilated at all times.
• Repair leaking exhaust pipework immediately.

WARNING

High level of engine noise when the engine is running.
Risk of damage to hearing!
• Wear ear protectors.

Engine – Test run

1.

Start engine (→ Page 72).

2.

Perform test run not below 1/3 load and at least until steady-state temperature is reached.

3.

Carry out operational checks (→ Page 70).

4.

Stop engine (→ Page 73).

156 | Engine | MS15041/03E 2018-08

TIM-ID: 0000000870 - 009

Содержание 12V4000C*5 series


















































































































































































































































































































Отзывы:

Нет отзывов