MTS Sensors Temposonics T-Series Скачать руководство пользователя | Manualshive

Страница: 46 / 52

background image

46

Temposonics

®

TH CANbus ATEX / IECEx / CEC / NEC / KCs / EAC Ex certified / Japanese approval

Operation Manual

8. Technical data Temposonics

®

TH

Output

Interface

CAN-Fieldbus System according to ISO 11898

Data protocol

Corresponds to encoder profile DS 406 V3.1 (CiA Standard DS 301 V3.0)

Baud rate, kBit/s
Cable length, m

1000 800 500 250 125 50 20
< 25 < 50 < 100 < 250 < 500 < 1000 < 2500
The sensor will be supplied with ordered baud rate, which is changeable by customer

Measured value

Position / option: Multi-position measurement (2…4 positions)

Measurement parameters

Resolution

2 µm, 5 µm; velocity step size: See following table

For stroke lengths

having a

cycle time of

Velocity step size

at 5 µm position
resolution

at 2 µm position
resolution

Up to 2400 mm

1.0 ms

results in the following

velocity step size

0.5 mm/s

0.2 mm/s

Up to 4800 mm

2.0 ms

0.25 mm/s

0.1 mm/s

Up to 7620 mm

4.0 ms

0.125 mm/s

0.05 mm/s

Cycle time

1.0 ms up to 2400 mm stroke length
2.0 ms up to 4800 mm stroke length
4.0 ms up to 7620 mm stroke length

Linearity deviation

7

< ±0.01 % F.S. (minimum ±40 μm)

Repeatability

< ±0.001 % F.S. (minimum ±2.5 µm) typical

Hysteresis

< 4 µm typical

Temperature coefficient

< 15 ppm/K typical

Operating conditions

Operating temperature

−40…+75 °C (−40…+167 °F)

Humidity

90 % relative humidity, no condensation

Ingress protection

Version D, G, and E: IP66 / IP67 (if properly connected by means that support IP66 / IP67
(pipe, gland, etc.))
Version N: IP66, IP67, IP68, IP69K, NEMA 4X, depending on cable gland

Shock test

100 g (single shock), IEC standard 60068-2-27

Vibration test

15 g / 10…2000 Hz, IEC standard 60068-2-6 (excluding resonant frequencies)

EMC test

Electromagnetic emission according to EN 61000-6-3
Electromagnetic immunity according to EN 61000-6-2
The sensor meets the requirements of the EU directives and is marked with

Operating pressure

350 bar static (5076 psi static)

Magnet movement velocity

8

Any

Design / Material

Sensor electronics housing

Stainless steel 1.4305 (AISI 303); option: Stainless steel 1.4404 (AISI 316L)

Flange

See “Table 1: TH rod sensor threaded flange type references” on page 12

Sensor rod

Stainless steel 1.4306 (AISI 304L); option: Stainless steel 1.4404 (AISI 316L)

Stroke length

25…7620 mm (1…300 in.)

7/

With position magnet # 201 542-2

8/

If there is contact between the moving magnet (including the magnet holder) and the sensor rod, make sure that the maximum speed of the moving magnet is ≤ 1 m/s

(Safety requirement due to ESD [Electro Static Discharge])

See next page for “Mechanical mounting”

«
...
44
45
46
47
48
...
»

Содержание Temposonics T-Series





















































Отзывы:

Нет отзывов

Похожие инструкции для Temposonics T-Series

Бренд: Panasonic Страницы: 132

EASA-PHONE KX-T30810

Бренд: Panasonic Страницы: 16

Бренд: Banner Страницы: 12

Бренд: Valore Страницы: 5

Бренд: Ignition Страницы: 1

Oakville Series

Бренд: Napoleon Страницы: 72

Бренд: Napoleon Страницы: 4

Allure Vertical Series

Бренд: Napoleon Страницы: 120

Бренд: National Instruments Страницы: 11

Бренд: Yakima Страницы: 12

Бренд: JEHNERT SOUND DESIGN Страницы: 8

Experience Series

Бренд: Rainbow Страницы: 19

Бренд: Yakima Страницы: 12

Бренд: Aptina Страницы: 147

MultiConnect Conduit Series

Бренд: Multitech Страницы: 2

Бренд: Sensit Страницы: 4

Бренд: Whispbar Страницы: 14

Бренд: Manhattan Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды