MTD 790 TB-TrimmerBlower, Руководство пользователя, Страница: 10 / 15

Operating instruction English
7
8. Shoulder belt holder
9. ON/OFF switch / ignition switch
10. Throttle
11. D-shaped handle
12. EZ-Link™
13. Shaft
14. Cutting attachment cover
15. Toggle
16. Toggle lock
17. Blower
18. Cutting attachment
19. Line cutting blade
20. Spacing collar
Fig. 2–3
1. D-shaped handle
2. Shaft
3. Shaft handle
4. Screw
5. Washer
6. Wingnut
7. Min distance 15.2 cm
8. Shoulder belt holder
9. Spacing collar
Fig. 4–6
(Depending on model)
1. EZ-Link™
2. Release button
3. Button
4. Guide groove
5. Main hole
6. Upper shaft tube
7. Lower shaft tube
Fig.7–8
1. Lock pin
2. Mount
3. Nut
4. Screw
Fig. 9–11
1. Throttle
2. ON/OFF switch / ignition switch
3. Full choke position (1) *
4. Half choke intermediate
position (2) *
5. Operating position (3) *
6. Choke lever *
7. Intake pump/primer
8. Starter rope
* Depending on model
Fig. 13–14
1. Toggle
2. Toggle lock
Fig. 19–20
1. Choke lever
( Depending on model)
2. Screw
3. Air filter
Fig. 24–25
1. Idle speed controller
2. Spark plug
Installation manual
Installing the D-shaped handle
n
For your safety the D-shaped
handle must be installed before
the distance collar. Push down
the handle bar over the shaft
so that the handle is at angle
to the engine (Fig. 2).
'EYXMSR
(SRSXTYWLXLI(WLETIHLERHPI
FEVSZIVXLIHMWXERGIGSPPEV
3XLIV[MWIXLILERHPIFEVSVYRMX
QE]FIHEQEKIH
n
Attach and tighten bolt, washer
and wing nut.
Adjusting the D-shaped
handle
n
Loosen the wing screw. It is not
required to remove the screws
and the washer.
n
Rotate the D-shaped handle
until the handle is positioned over
the shaft. Minimum distance
15.2 cm (Fig. 2).
n
While holding the unit in the
operating position (Fig. 12), move
the D-shaped handle into the
position which ensures the best
possible handling of the unit and
tighten the wing screw (Fig. 2).
Attaching and adjusting
the shoulder belt (Depending
on model)
n
Pull the belt through the buckle.
n
Pull the shoulder belt over your
head and place the pad on your
shoulder.
n
Latch the hook of the shoulder
belt into the metal holder (Fig. 3).
Adjust the belt to a comfortable
length.
Using the EZ-LINK
TM
system
Note
To facilitate installation and removal
of attachments, place the unit on the
ground or a workbench.
Removing cutter/blower
and other attachments
n
To loosen the attachment, rotate
the screw handle (3) to the left
(Fig. 6).
n
Press and hold down the release
button (2) (Fig. 4).
n
Hold the upper shaft housing (7)
securely and pull the attachment
directly out of the EZ-Link
TM
coupling (Fig. 5).
Installing the cutter/blower
and other attachments
n
To loosen the attachment, rotate
the screw handle to the left
(Fig. 6).
n
Hold the attachment securely and
push directly into the EZ-Link
TM
coupling (Fig. 5).
Note
Alignment of the release button (2)
with the guide groove (4) facilitates
installation (Fig. 4).
n
Secure the attachment by rotating
the button (3) to the right (Fig. 6).
Before operating the unit, ensure
that the rotary handle is secure.
Installing the cutter
attachment cover
n
Attach the cover with the guide
hole over the lock pin (1; Fig 7).
n
Align the cover so that its holes
agree with those in the locking
sleeve.
n
Attach the cover to the mount with
the screw (4) on the right and the
nut (3) on the left (Fig 8).
n
Check that the connections
sit tightly and correctly.