background image

Service Manual

MTD Products LLC - Product Training and Education Department

FORM NUMBER 769-01416

9/2004

31AS2B5 Snow Thrower

IMAGE SHOWS YARD-MAN UNIT

NOTE: These materials are for use by trained technicians who are experienced in the service and repair of outdoor power 
equipment of the kind described in this publication, and are not intended for use by untrained or inexperienced individuals.  
These materials are intended to provide supplemental information to assist the trained technician.  Untrained or inexperienced 
individuals should seek the assistance of an experienced and trained professional. Read, understand, and follow all instructions 
and common sense when working on power equipment. This includes the contents of the product’s Operators Manual, supplied 
with the equipment. No liability can be accepted for any inaccuracies or omission in this publication, although care has been 
taken to make it as complete and accurate as possible at the time of publication.  However, due to the variety of outdoor power 
equipment and continuing product changes that occur over time, updates will be made to these instructions from time to time.  
Therefore, it may be necessary to obtain the latest materials before servicing or repairing a product.  The company reserves the 
right to make changes at any time to this publication without prior notice and without incurring an obligation to make such 
changes to previously published versions. Instructions, photographs and illustrations used in this publication are for reference 
use only and may not depict actual model and component parts.  © Copyright 2005 MTD Products Inc. All Rights Reserved 

Содержание 31AS2B5














Отзывы: