background image

12 

4.4    Fan motor defrosting 
4.4.1 At defrosting, the compressor stops and fan motor keeps running, based on the regular time 
duration (Factory default setting is 12 min.). 

 

4.4.2 Defrosting logic: 

When system detects ambient temp.

 

13

, (

Default value: 13

), and compressor total running time 

for 

heating 

(Counted from the second of compressor starts, 

default value: 60 min.

) reaches 60 min, it will enter 

regular defrosting mode: compressor stops and fan motor keeps running 12 min. (

Default value: 12 min.

).   

Once finished, the compressor will restart to heat,

 counting for total heating time will be returned to zero. 

During fan motor defrosting: 

 

If the heat pump is switched off, it will stop to run immediately; 

 

If any error occurs and activates system protection, it will quit defrosting and stop to run;

 

 

The system will not detect low pressure protection. 

   

4.5    Parameter query 

 

Press       

,

 

it will enter the parameter query, press          or

       

to choose the code d0 to 

d8

press      , it will show current value. Then press            again to return to parameter query interface. 

When finished, shortly press          to exit.     

 

Code 

Parameter 

Spec. 

scope 

Default 

Remarks 

d0 

Ambient temp. 

-20-80 

 

 

Actually measured value 

d1 

Outlet water temp. 

-20-80 

 

 

Actually measured value 

d2 

Discharge temp. 

-20-140 

 

 

Actually measured value 

d4 

Compressor 

ON / OFF 

 

Actually measured value 

d5 

Fan motor 

ON / OFF 

 

Actually measured value 

d8 

Low pressure switch 

ON / OFF 

 

Actually measured value 

Notice:   

(1). The required sensor’s spec.: 50K for discharge temp. sensor and 5K for others, please note if users need to 
replace a new one, the same spec must be selected, otherwise it will not be matched with the PCB. 
(2). For the parameter c0 to c14 and H0 to H5, it is not authorized to set at end-users side, if actually needed, 
please contact your supplier; 
 

4.6    System protection 

4.6.1    Compressor discharge over high protection

 

When the compressor runs, the system will check discharge temp., if detects it

 105

 within 5S continuously, the 

system will judge it as discharge error, stop compressor and fan motor, show “E03” error code. 
When discharge temp.

 

parameter c3 (105

)- 20

, it will start fan motor and compressor (if remains stopped 

more than 3 minutes). 
If this error appears 3 times within 30 minutes, the system will lock on it, the 2 indication LED lights will flash 
together, and show error code “E13”, it can be only recovered by turning off the power supply. 

 

4.6.2    Low pressure protection

 

When the compressor runs for 5 minutes, if the system detects low pressure switch off within 10S continuously, it 
will enter this protection and show “EL” error code. When it detects low pressure switch connected, then quites 
this protection. 

Содержание FO045HS


















Отзывы: