background image

AUTOTRONIC CONTROLS CORPORATION

 • 1490 HENRY BRENNAN DR., EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344

IMPORTANT

Read these instructions before attempting this installation!

NOTE:

1. Solid Core spark plug wires 

cannot

 be used with an MSD DIS Ignition.

2. Vehicles originally equipped with a CD ignition 

cannot

 use an MSD DIS Ignition.

MSD Digital DIS-2 Dual Channel Ignition

PN 6211

MSD Digital DIS-4 Multi Channel Ignition

PN 6215

The MSD Digital DIS-2 Dual Channel Ignition can be used on 4-cylinder engines equipped with

two dual output coils. The MSD Digital DIS-4 Multi Channel Ignition can be used on 4, 6 or 8-cylinder
engines equipped with up to four dual output coils. The MSD Digital DIS Ignition will accept trigger
inputs from electronic DIS type ignition systems.

Parts Included

  1 - MSD Digital DIS-2 or DIS-4 Ignition
12 - Connectors, Butt Splice
  2 - Program Switch Covers
  1 - Cable Assembly
  1 - Bypass Plug

NOTE:

It is recommended that you have the Service Manual and wiring diagram for your vehicle

before beginning the installation of the MSD Digital DIS Ignition.

TECHNICAL FEATURES - DIGITAL DIS-2

TECHNICAL FEATURES - DIGITAL DIS-4

WARNING:

 Before installing the MSD Digital DIS Ignition, disconnect the battery cables. When

disconnecting the battery cables, always remove the Negative (-) cable first and install

it last.

Parts not included but may be needed

Tach/Fuel Adapter(s)
PN 8912

Operating Voltage:
Operating Current:
RPM Capability:
Ignition Inputs:
Ignition Outputs:
LED Indicator:
Tach Output:

Rev Limiter:

Spark Duration:
Energy Output Max:

Output Voltage:

Weight & Size:
Potting:

10-18 volts (neg. ground)
4.0 Amperes @ 10,000 RPM
14,000 RPM - 4-Cyl. @ 14 volts
2 - DIS Type
2 - DIS Type
Ign. trigger, low battery voltage
(+) 12 volt square wave,
40° duration
High RPM - Adjustable
Low RPM - Adjustable
20°- 4-Cyl. Max Sparks - 12
105-115 milliJoules per spark.
1540 milliJoules per sequence.
Primary (Into Coil): 460-480 volts
Secondary: (w/stock coil)
40,000 volts
3.7 lbs., 8.5"L x 4.5"W x 2.2"H
Ciba Polyurethane

Operating Voltage:
Operating Current:
RPM Capability:
Ignition Inputs:
Ignition Outputs:
LED Indicator:
Tach Output:

Rev Limiter:

Spark Duration:
Energy Output Max:

Output Voltage:

Weight & Size:
Potting:

10-18 volts (neg. ground)
7.4 Amperes @ 10,000 RPM
14,000 RPM - 4, 6, 8-Cyl. @ 14 volts
2, 3, 4 - DIS Type
2, 3, 4 - DIS Type
Ign. trigger, low battery voltage
(+) 12 volt square wave,
40° Duration
High RPM - Adjustable
Low RPM - Adjustable
20°- 4, 6, 8-Cyl. Max Sparks - 12
105-115 milliJoules per spark.
1540 milliJoules per sequence.
Primary (Into Coil): 460-480 volts
Secondary: (w/stock coil)
40,000 volts
4.5 lbs., 9.5"L x 4.5"W x 2.2"H
Ciba Polyurethane

Содержание 6211

















Отзывы: